Forum: RIBs & ribbing
05 April 2017, 17:42
|
Replies: 0
Views: 909
Where to put a trolling motor?
rather than repower my aging 13' RIB with a quiet, smooth 4-stroke, I was looking for a way to attach an electric trolling motor somewhere. There's no room on the transom.
Fiberglass bottom with...
|
Forum: RIBs & ribbing
02 October 2015, 00:59
|
Replies: 24
Views: 4,963
|
Forum: RIBs & ribbing
01 October 2015, 21:48
|
Replies: 24
Views: 4,963
yes sir, I do..
I bought a hypalon patch kit with hypalon glue and hypalon patches, sand paper. I haven't moved forward with it yet because:
-last weekend it was still bubbling the internal sealant.
-It has been...
|
Forum: RIBs & ribbing
01 October 2015, 18:52
|
Replies: 24
Views: 4,963
|
Forum: RIBs & ribbing
01 October 2015, 18:51
|
Replies: 24
Views: 4,963
|
Forum: RIBs & ribbing
01 October 2015, 16:01
|
Replies: 24
Views: 4,963
Hey guys
I couldn't get the valve out so I...
Hey guys
I couldn't get the valve out so I couldn't remove what water there was inside. I'm sure it was a small amount.
I used the sealant from WM and at first it would bubble out the leak....
|
Forum: RIBs & ribbing
24 September 2015, 15:59
|
Replies: 24
Views: 4,963
|
Forum: RIBs & ribbing
23 September 2015, 19:03
|
Replies: 24
Views: 4,963
even with a heavy RIB?
I thought those internal sealants worked mostly on soft inflatables that you could shake around to distribute the stuff around the tube?
I tried an external patch today (actually that stretch-tape...
|
Forum: RIBs & ribbing
22 September 2015, 17:30
|
Replies: 24
Views: 4,963
Hypalon patch
This is the first time I've had a significant enough leak in one of my tubes to do a patch. It produces bubbles from underneath when I'm inflating in the water.
There seem to be a lot of options...
|
Forum: RIBs & ribbing
06 August 2015, 13:35
|
Replies: 5
Views: 3,355
haha newbie pics
I had to search my computer for any pics of boat's transom and this is as good as it gets. The one that is upside down actually shows a good view of the corroded release valve and the bottom part of...
|
Forum: RIBs & ribbing
06 August 2015, 13:24
|
Replies: 5
Views: 3,355
|
Forum: RIBs & ribbing
04 August 2015, 23:40
|
Replies: 5
Views: 3,355
tilt/trim options for my 35 hp Johnson
It appears that at least the trim motor and possibly the tilt cylinder are shot on my 13' RIB Johnson 35 hp 2 stroke. A full replacement of the unit is about $1100 and and I;m guessing about $300 in...
|
Forum: Engines & props
05 July 2015, 15:05
|
Replies: 3
Views: 686
|
Forum: Engines & props
04 July 2015, 19:04
|
Replies: 3
Views: 686
|
Forum: Engines & props
04 July 2015, 16:07
|
Replies: 3
Views: 686
Troubleshooting trim motor 35 hp Johnson
Trim motor slowed down to a crawl after a rainstorm and then stops altogether. The battery is fine. I can hear gurgling noise from the trim motor when I try to operate. I have never personally...
|
Forum: RIBs & ribbing
04 July 2015, 15:46
|
Replies: 10
Views: 2,371
|
Forum: RIBs & ribbing
16 May 2014, 02:59
|
Replies: 10
Views: 2,371
|
Forum: RIBs & ribbing
15 May 2014, 17:13
|
Replies: 10
Views: 2,371
four blade prop for following seas?
My boat seems to really bog down in following seas, to the point that it scares me a little. It is a 13' AB console with 35hp Johnson.
Is there any point in trying out a four-blade prop to...
|
Forum: RIBs & ribbing
15 May 2014, 17:10
|
Replies: 5
Views: 938
|
Forum: RIBs & ribbing
13 May 2014, 02:57
|
Replies: 5
Views: 938
Thanks fellas. These all seem like fixable,...
Thanks fellas. These all seem like fixable, relatively inexpensive problems. I was fearing catastrophic engine failure, gear case slipping, or costly fiberglass work!
One other interesting fact:...
|
Forum: RIBs & ribbing
12 May 2014, 05:33
|
Replies: 5
Views: 938
Random engine surging, then overheat!
Hi All:
Heading into my third summer of RIB ownership and I am learning a lot (and spending not a little). 13' 1998 AB with seat and right-hand console.
I am befuddled by a very intermittent...
|
Forum: Electrics and electronics
27 August 2013, 02:05
|
Replies: 5
Views: 1,671
Sorry to 'jack this post but it seems like the...
Sorry to 'jack this post but it seems like the perfect spot for my similar question...
I bought a Lowrance Mark 4 pro and bought a suction cup transom mount. I've tried various positions on the...
|
Forum: RIBs & ribbing
27 August 2013, 01:39
|
Replies: 9
Views: 1,835
Prop helped with RPMs, gave me a little oomph
The 4-blade prop was a 16 pitch! I don't really know why they would have done that. This season I barely made 4100 rpms with the prop.
Switched to a 3-blade 13 pitch prop. WOT can exceed 6000rpm...
|
Forum: RIBs & ribbing
04 September 2012, 16:47
|
Replies: 9
Views: 1,835
My ab rib...
Thanks for the prop info! My ab handles perfectly, having only had it on the water for 5 days total. There appears to be a VERY gradually leak somewhere but the fabric looks fine. I want to have the...
|
Forum: RIBs & ribbing
03 September 2012, 03:53
|
Replies: 9
Views: 1,835
Must go faster!!!
Hey all this is my first post. I just bought a second hand 13' AB RIB with right console and a 35 hp 2 stroke 3 cyl Johnson. It was owned by the Maine game wardens.
Right now with 2-3 people...
|