Forum: Inflatable boats - SIBs and folding RIBs
14 September 2011, 23:31
|
Replies: 3
Views: 1,348
|
Forum: Inflatable boats - SIBs and folding RIBs
17 August 2011, 22:56
|
Replies: 4
Views: 2,851
|
Forum: Inflatable boats - SIBs and folding RIBs
10 August 2011, 17:59
|
Replies: 20
Views: 24,497
|
Forum: Upcoming RIB cruises
30 July 2011, 23:51
|
Replies: 4
Views: 1,138
|
Forum: Inflatable boats - SIBs and folding RIBs
25 July 2011, 22:29
|
Replies: 32
Views: 7,207
|
Forum: Inflatable boats - SIBs and folding RIBs
25 July 2011, 19:01
|
Replies: 32
Views: 7,207
You can launch at the beach/slip next to the...
You can launch at the beach/slip next to the sailing club. We always launch there, then go up the river or out of the piers to the coast. Gets a bit messy in the piers with the river and sea meeting....
|
Forum: Inflatable boats - SIBs and folding RIBs
24 July 2011, 22:49
|
Replies: 32
Views: 7,207
|
Forum: RIBs & ribbing
09 July 2011, 23:38
|
Replies: 8
Views: 1,960
Could you trim the lifted/cut edge perfectly...
Could you trim the lifted/cut edge perfectly parallel with the bottom/glued edge. Take off as much material as safely possible, or whatever looks proportionately best, leaving you with a neat red...
|
Forum: Inflatable boats - SIBs and folding RIBs
09 July 2011, 14:46
|
Replies: 1
Views: 1,157
Zodiac floor tension
Hi all.
I am replacing the piece of wood on the inside of the transom that the rear most floor board sits under. I don't think the rotten one that is on is the original, so I'm reluctant to use...
|
Forum: Inflatable boats - SIBs and folding RIBs
27 June 2011, 22:54
|
Replies: 1
Views: 1,152
|
Forum: Inflatable boats - SIBs and folding RIBs
27 June 2011, 22:50
|
Replies: 1
Views: 1,152
Day on the Tyne
Day out on Sunday. Had a little experiment with transom height. Raised it about 10mm and it cavitated non stop. lowered it back down and was fine in nothing more than the second hole from transom....
|
Forum: Inflatable boats - SIBs and folding RIBs
24 June 2011, 17:29
|
Replies: 5
Views: 1,712
|
Forum: Bits and pieces
24 June 2011, 15:44
|
Replies: 4
Views: 1,751
|
Forum: Bits and pieces
23 June 2011, 21:51
|
Replies: 4
Views: 1,751
|
Forum: Bits and pieces
23 June 2011, 19:51
|
Replies: 4
Views: 1,751
|
Forum: Inflatable boats - SIBs and folding RIBs
22 June 2011, 21:24
|
Replies: 7
Views: 3,445
Hi.
I am going to used closed cell foam and...
Hi.
I am going to used closed cell foam and make a mattress like the RNLI do. You can buy it in various thicknesses and have it cut to size. If you do a search for closed cell foam on ebay there...
|
Forum: Inflatable boats - SIBs and folding RIBs
07 May 2011, 13:43
|
Replies: 3
Views: 1,809
|
Forum: Inflatable boats - SIBs and folding RIBs
06 May 2011, 17:46
|
Replies: 3
Views: 1,809
|
Forum: Inflatable boats - SIBs and folding RIBs
05 May 2011, 21:53
|
Replies: 3
Views: 1,809
PVC Grand Raid
Hi all, just a quick question for the Zodiac experts!
Am I right in thinking all GRs are hypalon apart from a couple of years when they were made from pvc? Does anyone know which years?
...
|
Forum: Inflatable boats - SIBs and folding RIBs
25 April 2011, 17:05
|
Replies: 3
Views: 3,292
Thanks for the replys. We went out today on the...
Thanks for the replys. We went out today on the Tyne again sailing all the way under the bridges finally. It was great unfortunately we forgot the camera again! Tom sat on a life jacket on the floor...
|
Forum: Inflatable boats - SIBs and folding RIBs
22 April 2011, 20:01
|
Replies: 3
Views: 3,292
Speed Tubes
Hi all.
The last time out we went up the River Tyne and encountered a fair amount of wind driven chop on the more exposed sections of water. I reduced the throttle and tried to navigate the chop...
|
Forum: Inflatable boats - SIBs and folding RIBs
21 April 2011, 20:00
|
Replies: 7
Views: 2,589
|
Forum: Bits and pieces
20 April 2011, 18:42
|
Replies: 6
Views: 1,365
|
Forum: Inflatable boats - SIBs and folding RIBs
20 April 2011, 16:17
|
Replies: 7
Views: 2,589
A thrust board is a plank that is fixed to the...
A thrust board is a plank that is fixed to the tubes where they meet the hull and on mine it is positioned just before the bow section. The floor boards get tensioned between the thrust board and the...
|
Forum: Bits and pieces
19 April 2011, 17:13
|
Replies: 6
Views: 1,365
|