Forum: Bits and pieces
01 August 2018, 22:12
|
Replies: 0
Views: 423
Evinrude 60 etec parts
Hi All,
I’m in need of the side panels for a blue etec, and a cover if possible for a sea cadet safety boat, anyone know of any engines being broken up?
Cheers Lee.
|
Forum: Electrics and electronics
22 February 2017, 21:58
|
Replies: 7
Views: 1,230
|
Forum: Electrics and electronics
19 February 2017, 23:04
|
Replies: 7
Views: 1,230
|
Forum: Electrics and electronics
19 February 2017, 18:51
|
Replies: 7
Views: 1,230
Big electrical items for sale
Hi All,
Apologies if this is not for this forum, The sea cadets I help with have two bigger boat items for sale and we are unsure where would be the best place to sell them. We have a Victron 24v...
|
Forum: Engines & props
04 September 2016, 20:52
|
Replies: 324
Views: 496,319
|
Forum: Bits and pieces
28 August 2016, 06:16
|
Replies: 0
Views: 661
Stainless Steel Prop Deflector
A charity I volunteer for have a unused stainless prop deflector for a 50hp Mariner, serial number 12791 for sale. These things are around £475 new we are looking for £250. It is located near...
|
Forum: Engines & props
03 June 2016, 23:15
|
Replies: 8
Views: 1,704
Thanks all, for your suggestions.
It's...
Thanks all, for your suggestions.
It's running fine now, I ended up having to take the exhaust manifold off and having a good clean through with a variety of cable ties to remove loads of salt.
...
|
Forum: Engines & props
01 June 2016, 20:55
|
Replies: 8
Views: 1,704
|
Forum: Engines & props
01 June 2016, 11:10
|
Replies: 8
Views: 1,704
|
Forum: Engines & props
30 May 2016, 23:56
|
Replies: 8
Views: 1,704
1999 15hp Honda weak telltale
Hi All, I have just been given the use of a little valiant rib with a Honda 4 stroke outboard with a telltale issue. A dribble at low revs, disappears with higher revs. I have already changed the...
|
Forum: Engines & props
16 December 2014, 08:39
|
Replies: 58
Views: 17,677
Hi All
After a busy summer I have managed to...
Hi All
After a busy summer I have managed to start looking at the engine again, this is where I'm at.
I dismantled the carbs and carb three was full of gunk, with the air inlets that enters at...
|
Forum: Engines & props
25 August 2014, 18:05
|
Replies: 4
Views: 1,110
etec 60 power trim problem
Hi All
The power trim on my 60hp etec is not working, tried both buttons on engine and morse box, all I get is a clicking noise.
Any suggestions?
Cheers
Lee
|
Forum: Engines & props
15 May 2014, 18:46
|
Replies: 1
Views: 910
Mariner 15 hp 2 stroke help.
Hi gang
I have recently replaced the carb gaskets etc on a mid 90s mariner. When it has ran for a while its great, but its a bugger to get started. The mixture screw is set to 1 1/4 from lightly...
|
Forum: Engines & props
13 April 2014, 20:10
|
Replies: 58
Views: 17,677
|
Forum: Engines & props
12 April 2014, 21:28
|
Replies: 58
Views: 17,677
|
Forum: Engines & props
10 April 2014, 11:43
|
Replies: 58
Views: 17,677
Hi all
Thanks for the help, the 103 carbs...
Hi all
Thanks for the help, the 103 carbs are working ok. The main starting issue was a knackered battery cable as well as gummed up carbs.
Does anyone know how to adjust the idle jet up...
|
Forum: Engines & props
29 March 2014, 22:20
|
Replies: 2
Views: 1,221
Online engine manuals
Hi All
I have recently found a we site which maybe of interest
Boatinfo - The library, containing manuals, brochures and other technical documents from the last hundred years!...
|
Forum: Engines & props
23 March 2014, 21:27
|
Replies: 6
Views: 4,880
|
Forum: Engines & props
23 March 2014, 19:28
|
Replies: 6
Views: 4,880
Quicksilver pull to push conversion
I have searched the net, but I cannot seem to find how to convert a quicksilver control box from pull to throttle to push to throttle.
Any ideas anyone?
Cheers
Lee
|
Forum: Bits and pieces
10 March 2014, 21:02
|
Replies: 26
Views: 3,672
|
Forum: Bits and pieces
05 March 2014, 20:30
|
Replies: 26
Views: 3,672
|
Forum: Engines & props
24 February 2014, 18:22
|
Replies: 58
Views: 17,677
|
Forum: Bits and pieces
24 February 2014, 18:09
|
Replies: 26
Views: 3,672
|
Forum: Bits and pieces
20 February 2014, 22:38
|
Replies: 26
Views: 3,672
|
Forum: Bits and pieces
16 February 2014, 22:50
|
Replies: 26
Views: 3,672
|