Forum: Engines & props
31 March 2018, 12:23
|
|
Replies: 1
Views: 1,678
Sorted.
The carb was left empty for a month...
Sorted.
The carb was left empty for a month or two, and I'm assuming the float stuck open so the bowl over filled.
Have filled the bowl with cleaner, then run the engine with a heavily...
|
|
Forum: Engines & props
30 March 2018, 15:14
|
|
Replies: 1
Views: 1,678
Suzuki DT25 Fuel Leaking out of carb
I noticed some fuel dripping from the top carburetor. Can't really see where exactly as I'll need to remove the oil reservoir (and the weather is shocking) but it's out of a hole cast in the carb on...
|
|
Forum: Engines & props
22 January 2018, 20:43
|
|
Replies: 3
Views: 4,278
Injector Cleaner for Suzuki 4 Strokes
We've got a couple of safety boats at the club with varying sizes of Suzuki 4 stroke engines. They don't get driven hard, spending most of the time at little more than idle, and every now and again...
|
|
Forum: Engines & props
04 August 2017, 19:10
|
|
Replies: 0
Views: 705
New steering cable. A bit heavy and 'clicky'
I've just replaced a steering cable for the first time, as the steering was stiff in places with some play in the wheel.
With the new cable the steering is smooth with no play, but feels a bit...
|
|
Forum: Engines & props
22 April 2017, 12:44
|
|
Replies: 31
Views: 5,900
Did you tell the police?
I'm guessing it...
Did you tell the police?
I'm guessing it might have been the same people that tried to steal the engines from the sailing club last week. Didn't manage to take anything, but cut all the cables :-(
|
|
Forum: Engines & props
22 April 2017, 12:32
|
|
Replies: 31
Views: 5,900
|
|
Forum: Engines & props
24 March 2017, 08:04
|
|
Replies: 3
Views: 1,138
|
|
Forum: Engines & props
23 March 2017, 20:35
|
|
Replies: 3
Views: 1,138
Suzuki DT25: Flush muffs?
We don't get any water pumping when trying to use flush muffs. Is it worth getting a better set that seal around the intakes better, or is it something that just doesn't work very well?
|
|
Forum: Engines & props
12 February 2017, 14:23
|
|
Replies: 2
Views: 2,284
Suzuki DT25: what diameter fuel line?
I'm going to replace fuel tank, all lines and fittings. Any recommendations as to the fuel line diameter (plus anything else I should consider)?
Thanks
|
|
Forum: Engines & props
28 January 2017, 18:12
|
|
Replies: 7
Views: 1,156
Makes sense. Just got to decide if I'm brave...
Makes sense. Just got to decide if I'm brave enough to take the springs out and clean them up without having a spare to hand. If one pings across the boatyard tomorrow's fun is cancelled!
|
|
Forum: Engines & props
28 January 2017, 16:18
|
|
Replies: 7
Views: 1,156
|
|
Forum: Engines & props
28 January 2017, 15:56
|
|
Replies: 7
Views: 1,156
According to the diagrams they have springs. I...
According to the diagrams they have springs. I haven't taken them all the way out cos I have a pretty embarrassing record of dropping fiddly bits into the engine!
If they're not expensive I'll...
|
|
Forum: Engines & props
28 January 2017, 13:21
|
|
Replies: 7
Views: 1,156
Idle screws working loose? Suzuki DT25
I'm getting my DT25 idling nicely (about 1 1/4 turns) but after a bit of use it starts to sneeze at idle, then cut out.
When I try and set it up again the screws are further out. Has anyone...
|
|
Forum: Engines & props
21 January 2017, 18:46
|
|
Replies: 14
Views: 2,383
|
|
Forum: Engines & props
15 January 2017, 17:52
|
|
Replies: 14
Views: 2,383
|
|
Forum: Engines & props
15 January 2017, 15:26
|
|
Replies: 14
Views: 2,383
|
|
Forum: Engines & props
15 January 2017, 15:24
|
|
Replies: 14
Views: 2,383
|
|
Forum: Engines & props
15 January 2017, 11:31
|
|
Replies: 14
Views: 2,383
|
|
Forum: Engines & props
15 January 2017, 10:52
|
|
Replies: 14
Views: 2,383
'Plume' of water from engine
I've got a Suzuki dt25 on the back of a Porter's 4.5m rib, with anti-cavitation hydrofoil fitted.
I get a noticeable plume of water off the back of the engine, even at relatively low speeds.
...
|
|
Forum: RIBs & ribbing
08 January 2017, 17:41
|
|
Replies: 2
Views: 813
|
|
Forum: RIBs & ribbing
07 January 2017, 21:03
|
|
Replies: 2
Views: 813
Removing anti-foul
Is there a safe way to remove anti-foul without damaging the tubes?
Apologies if this is already been answered somewhere - my tablet won't let me use the search facility.
|
|
Forum: Engines & props
06 June 2016, 18:23
|
|
Replies: 5
Views: 976
Fixed the same thing on mine yesterday by...
Fixed the same thing on mine yesterday by replacing the battery connectors with new ones.
The old connectors were really skanky, so it was an obvious thing to try, but the symptoms were the same...
|
|
Forum: Engines & props
05 June 2016, 07:05
|
|
Replies: 8
Views: 3,238
|
|
Forum: Engines & props
30 May 2016, 21:11
|
|
Replies: 8
Views: 3,238
|
|
Forum: Engines & props
13 May 2016, 16:17
|
|
Replies: 8
Views: 3,238
|
