Forum: RIBs & ribbing
26 March 2013, 03:04
|
Replies: 15
Views: 6,521
|
Forum: Engines & props
02 December 2011, 11:05
|
Replies: 22
Views: 4,174
Hi All
thanks for your replies
The RIB...
Hi All
thanks for your replies
The RIB is made by East Coast Ribs and the Rib and engine were bought separately and put together ourselves.
Tried all trim angles, down to start with and...
|
Forum: Engines & props
21 November 2011, 08:34
|
Replies: 22
Views: 4,174
|
Forum: Engines & props
20 November 2011, 21:30
|
Replies: 22
Views: 4,174
|
Forum: Engines & props
20 November 2011, 21:28
|
Replies: 22
Views: 4,174
|
Forum: Engines & props
20 November 2011, 20:57
|
Replies: 22
Views: 4,174
|
Forum: Engines & props
20 November 2011, 20:53
|
Replies: 22
Views: 4,174
|
Forum: Engines & props
20 November 2011, 20:27
|
Replies: 22
Views: 4,174
First run on new RIB
Hi All
So today was the first run on my friends new RIB, 5.2m with 90 merc.
Straight off the bat it is porpoising all over the place, flat calm and its like being on a bucking bronco !
Also...
|
Forum: Engines & props
20 November 2011, 20:21
|
Replies: 9
Views: 2,414
|
Forum: Engines & props
20 November 2011, 19:46
|
Replies: 13
Views: 2,509
What engine is it ?
I think some, Mercs and...
What engine is it ?
I think some, Mercs and Mariners for instance have a feature that trims you down if you throttle hard when the engine is raised too high, could it be a problem with this ?
|
Forum: Engines & props
19 November 2011, 10:28
|
Replies: 9
Views: 2,414
|
Forum: Engines & props
19 November 2011, 08:35
|
Replies: 9
Views: 2,414
|
Forum: Engines & props
19 November 2011, 08:14
|
Replies: 9
Views: 2,414
Custom fuel tanks
Does anyone know of a supplier of custom made plastic fuel tanks ?
A friend purchased a half finished project and the locker where you would put the fuel tank is a funny size, it would take a...
|
Forum: Engines & props
30 October 2011, 09:46
|
Replies: 22
Views: 4,048
B&O, I am very thankful for your help, you are...
B&O, I am very thankful for your help, you are obviously very experienced in what you are talking about and you have been kind enough to share your knowledge with me and from what I have read on the...
|
Forum: Engines & props
30 October 2011, 09:41
|
Replies: 22
Views: 4,048
|
Forum: Engines & props
30 October 2011, 08:32
|
Replies: 22
Views: 4,048
No, there are several different holes on an...
No, there are several different holes on an outboard bracket to allow you to adjust the height, the wrong height of the engine can affect performance a lot We would like to get as close to correct as...
|
Forum: Engines & props
30 October 2011, 05:48
|
Replies: 22
Views: 4,048
|
Forum: Engines & props
29 October 2011, 21:30
|
Replies: 22
Views: 4,048
Hi Boats and Outboards, yes, the bolt hole is...
Hi Boats and Outboards, yes, the bolt hole is what I am after help with. The RIB was brand new and had never been in the water however it did have an outboard fitted but never used so the holes are...
|
Forum: Engines & props
29 October 2011, 10:17
|
Replies: 22
Views: 4,048
New engine height
My mate is mounting a new engine on his new rib, any tips on how to work out the engine height ?
Its a 5.2 m rib with a long shaft engine on a 20" transom.
|
Forum: Upcoming RIB cruises
29 October 2011, 10:07
|
Replies: 45
Views: 14,455
|
Forum: Upcoming RIB cruises
29 October 2011, 10:04
|
Replies: 45
Views: 14,455
|
Forum: Engines & props
25 October 2011, 20:27
|
Replies: 2
Views: 1,132
|
Forum: Engines & props
25 October 2011, 20:26
|
Replies: 17
Views: 3,176
|
Forum: Engines & props
25 October 2011, 20:24
|
Replies: 12
Views: 2,660
|
Forum: Engines & props
24 October 2011, 22:38
|
Replies: 12
Views: 2,660
|