Forum: Bits and pieces
06 October 2020, 22:07
|
Replies: 2
Views: 531
|
Forum: Bits and pieces
03 September 2020, 17:42
|
Replies: 2
Views: 531
|
Forum: Bits and pieces
03 September 2020, 14:40
|
Replies: 0
Views: 179
Johnson Prop in good condition
This is a Johnson /Evinrude prop in good condition, 91/4 inch x 8 inch, fitted to a 9.9 /15hp 2 stroke but will surely fit any engine sharing the same gearbox from 70's to 90's?
One or two chips in...
|
Forum: Bits and pieces
03 September 2020, 14:21
|
Replies: 2
Views: 531
Johnson 9.9 2 stroke std shaft with L/S parts
1994 Johnson 2 stroke, very good runner in great condition, ready to use with fuel tank and line. serviced with new coils and fuel pump, new fuel lines and in-line filter, carb cleaned and gearbox...
|
Forum: Engines & props
03 September 2020, 10:13
|
Replies: 4
Views: 315
|
Forum: Engines & props
03 September 2020, 10:09
|
Replies: 4
Views: 315
Thank you both for the advice, I'll do both and...
Thank you both for the advice, I'll do both and keep my fingers crossed. Ebay seemed to prioritise the buyer in any disputes however contrived they are by the buyer, and also there's the fees, but as...
|
Forum: Engines & props
02 September 2020, 23:04
|
Replies: 4
Views: 315
Good places to advertise a 9.9 Johnson 2 stroke?
I've just serviced and sorted my little used, long serving 9.9 Johnson 2 stroke, 1994, but wondered where to advertise it - anyone had any good experiences with particular sites?
I've had some...
|
Forum: Engines & props
15 March 2020, 20:17
|
Replies: 49
Views: 29,676
|
Forum: Engines & props
15 March 2020, 19:56
|
Replies: 49
Views: 29,676
As it's been explained to me, it's only if the...
As it's been explained to me, it's only if the service is done by a recognised dealer that the warranty is valid.
According to the place i went to, Mercury are the only ones in their experience...
|
Forum: Engines & props
15 March 2020, 19:37
|
Replies: 49
Views: 29,676
|
Forum: Engines & props
09 March 2020, 22:50
|
Replies: 49
Views: 29,676
Glad to hear they’ve confirmed delivery, I...
Glad to hear they’ve confirmed delivery, I enquired about the scrappage via eBay with ‘another dealer’ and found a maze of confusing conditions, not what it first appeared to be. Maybe better to...
|
Forum: Engines & props
09 March 2020, 20:53
|
Replies: 49
Views: 29,676
|
Forum: Engines & props
09 March 2020, 20:01
|
Replies: 49
Views: 29,676
|
Forum: Engines & props
09 March 2020, 19:51
|
Replies: 49
Views: 29,676
Thanks, as I understand the 15 and 20hp tohatsu...
Thanks, as I understand the 15 and 20hp tohatsu Efi are the same weight, so it’s very tempting, but around £300 more - as it’s a bit of a stretch for the 15 I don’t think I can justify the 20 on our...
|
Forum: Engines & props
09 March 2020, 00:35
|
Replies: 49
Views: 29,676
|
Forum: Engines & props
09 March 2020, 00:07
|
Replies: 49
Views: 29,676
Thanks for the insight, did the extra weight...
Thanks for the insight, did the extra weight spoil the trim of the boat? I figured the extra weight to be similar to a full 12l fuel tank, so maybe not too much difference?
I need to strip the...
|
Forum: Bits and pieces
08 March 2020, 23:37
|
Replies: 29
Views: 2,067
Thanks Fenlander, I see - not what I expected!...
Thanks Fenlander, I see - not what I expected! I'd only just finished the posts on your Yamaha 15 maintenance where everything looks as new - the Mercury had a less carefully looked after appearance...
|
Forum: Bits and pieces
08 March 2020, 22:31
|
Replies: 29
Views: 2,067
The paint on the block of the Mercury looked...
The paint on the block of the Mercury looked lumpy like hammerite - I've been looking at a lot of 'under the hood' pictures lately and hadn't seen one like that.
There was /is a Suzuki DF15 in...
|
Forum: Engines & props
08 March 2020, 21:06
|
Replies: 49
Views: 29,676
|
Forum: Inflatable boats - SIBs and folding RIBs
09 October 2016, 19:27
|
Replies: 18
Views: 3,093
Hi Steve, yes I'd be very interested to see how...
Hi Steve, yes I'd be very interested to see how that turns out - I've looked at a variety of countersunk stainless set screws from ebay, plastic encased threaded fittings, like knobs for under the...
|
Forum: Inflatable boats - SIBs and folding RIBs
21 August 2016, 16:09
|
Replies: 9
Views: 3,461
But don't you still have to manually open or...
But don't you still have to manually open or close the valves?
I can't see any mechanism on the one linked to, which would turn the knurled centre to open or close the valve - unless you inflate...
|
Forum: Inflatable boats - SIBs and folding RIBs
21 August 2016, 15:13
|
Replies: 9
Views: 3,461
On my Halkey Roberts type of valve the adaptor...
On my Halkey Roberts type of valve the adaptor with the bayonet fitting that you show, doesn't open the valve when it is plugged in and turned. So you shouldn't be losing air just by plugging in the...
|
Forum: Inflatable boats - SIBs and folding RIBs
21 August 2016, 11:22
|
Replies: 18
Views: 3,093
|
Forum: Inflatable boats - SIBs and folding RIBs
20 August 2016, 17:38
|
Replies: 18
Views: 3,093
Thank, yes I saw those -
I was thinking about...
Thank, yes I saw those -
I was thinking about the PVC 'flange' the original seat bolts to, but I thing the type you've highlighted would do just as well £9.99 on ebay!
They have the two plastic...
|
Forum: Inflatable boats - SIBs and folding RIBs
20 August 2016, 13:28
|
Replies: 18
Views: 3,093
|