Showing results 1 to 9 of 9
Search took 0.00 seconds.
Search: Posts Made By: jcjcat
Forum: RIBs & ribbing 15 December 2011, 18:42
Replies: 10
Views: 4,069
Posted By jcjcat
Why do you want to block the tank with expandable...

Why do you want to block the tank with expandable foam ?
Not safe, and possible chemical reaction could be expected against SS, giving rust and holes.
I had this case in an italian rib, tank...
Forum: RIBs & ribbing 15 December 2011, 17:43
Replies: 15
Views: 3,204
Posted By jcjcat
In France, a lot of owners are complaining about...

In France, a lot of owners are complaining about destroyed injectors ...

If I had an Etec - or any other new, modern and expensive engine - I would invest in a Racor-Parker diesel filter, turbine...
Forum: Engines & props 21 October 2011, 08:32
Replies: 29
Views: 4,577
Posted By jcjcat
The engine torque is the right parameter to...

The engine torque is the right parameter to consider - not the peak power. Plus reliability indeed !

To get the torque high, I would suggest to choose the cubic inches nr as high as possible, and...
Forum: Engines & props 19 October 2011, 22:27
Replies: 8
Views: 4,600
Posted By jcjcat
your engine is set too high, the shaft should...

your engine is set too high, the shaft should stay 1 inch above the highjackers lower level
Forum: Engines & props 19 October 2011, 22:21
Replies: 4
Views: 5,370
Posted By jcjcat
Willk is right, the pee has no effect on the...

Willk is right, the pee has no effect on the cooling - just there to say that you have water pressure if not obstructed by insect nest - they like ...!

Replace the impeller, if not your engine is...
Forum: Engines & props 19 October 2011, 22:13
Replies: 14
Views: 2,726
Posted By jcjcat
Years ago, I made it using a 10mm thick steel...

Years ago, I made it using a 10mm thick steel plate, I drilled 3x 8mm holes at the right diameter and 120° angle to allow fixing 3 bolts into the corresponding flywheel holes, then a center hole to...
Forum: Engines & props 19 October 2011, 22:03
Replies: 5
Views: 2,924
Posted By jcjcat
I remember having seen this kind of repair 30...

I remember having seen this kind of repair 30 years ago, it was on a racing car crankshaft.

High strength steel had been added to the defective surface by projection (plasma ...?) then ground,...
Forum: RIBs wanted 10 May 2004, 22:24
Replies: 6
Views: 6,689
Posted By jcjcat
750 Tomcat

The pontoon has to be replaced, it will be made in hypalon with longitudinal cut, color on request.
The genuine diameter was 48cm, it will be raised to 60, with truncated cones, and 9 compartments.
Forum: RIBs wanted 10 May 2004, 22:21
Replies: 6
Views: 6,689
Posted By jcjcat
Tomcat 7.5m RIB with diesel engine

I have a 7.5m catamaran RIB, with a 120HP - Mercruiser 1.7DTI diesel engine, please have a look at my website www.lagaude-marine.com.
The boat has a very few hours (10) she has been used for testing...
Showing results 1 to 9 of 9

 


All times are GMT. The time now is 05:16.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.