Go Back   RIBnet Forums > Search Forums
Reload this Page Search Results
Click Here to Login

Join RIBnet Today
Showing results 1 to 14 of 14
Search took 0.00 seconds. Search: Posts Made By: beamishken
Forum: Trailers & towing 12 October 2014, 18:45
Replies: 70
Views: 12,163
Posted By beamishken
Where the spacers contact the back of the inside...

Where the spacers contact the back of the inside bearing they need to be small diameter to fit inside the seal which is pressed onto the bearing so they contact the metal of the bearing & not the...
Forum: Trailers & towing 12 October 2014, 09:40
Replies: 70
Views: 12,163
Posted By beamishken
Your set up looks like transverse leaf springs...

Your set up looks like transverse leaf springs with the stubs bolted below. I haven't seen them for a good while now & a quick Google didn't find any so maybe no longer available
You might be able...
Forum: Trailers & towing 06 October 2014, 20:05
Replies: 70
Views: 12,163
Posted By beamishken
mr headsocket despite what Peter c says the...

mr headsocket despite what Peter c says the suggestion of the centre race broken out of your old bearings used as a spacer will work fine

as others have said it might be exactly the right length...
Forum: Trailers & towing 05 October 2014, 20:40
Replies: 70
Views: 12,163
Posted By beamishken
See post #42 & your local store is probably...

See post #42

& your local store is probably 4000 miles from the op
Forum: Trailers & towing 05 October 2014, 08:14
Replies: 70
Views: 12,163
Posted By beamishken
Mrheadsocket if you use standard of the shelf...

Mrheadsocket if you use standard of the shelf washers the outside diameter will foul the grease seal that is why the old bearing inner race is such an easy fix
Peter C the op stated he wanted a...
Forum: Trailers & towing 04 October 2014, 21:44
Replies: 70
Views: 12,163
Posted By beamishken
& your going to turn a bearing? Stop digging...

& your going to turn a bearing?
Stop digging Peter!
Forum: Trailers & towing 04 October 2014, 20:12
Replies: 70
Views: 12,163
Posted By beamishken
yeh if it was only a 1mm spacer he needed then...

yeh if it was only a 1mm spacer he needed then possibly there might be a deviation in the bearing but he is 10mm short & needs 1-2mm overhang so 11-12 mm spacer needed which if its a tight fit to...
Forum: Trailers & towing 04 October 2014, 19:02
Replies: 70
Views: 12,163
Posted By beamishken
that's exactly what I meant too if there too...

that's exactly what I meant too
if there too long just grind to length to suit & if your worried fit the cut side towards the inside of the stub so the outer side the bearings are resting against is...
Forum: Trailers & towing 04 October 2014, 09:16
Replies: 70
Views: 12,163
Posted By beamishken
Looks like the shaft is a bit longer than...

Looks like the shaft is a bit longer than standard easiest solution would be to fit a spacer ring or washer behind the inner bearing to bring the hub forward


just a thought you could possibly...
Forum: Trailers & towing 26 September 2014, 07:41
Replies: 70
Views: 12,163
Posted By beamishken
Typical arrogant yank! WHEN YOUR IN A HOLE &...

Typical arrogant yank!

WHEN YOUR IN A HOLE & CANT GET OUT JUST STOP DIGGING!!!!!!!
Forum: Trailers & towing 25 September 2014, 19:51
Replies: 70
Views: 12,163
Posted By beamishken
Ive explained it twice the seal is totally...

Ive explained it twice the seal is totally different

take a look at these they are standard on the majority of small uk trailers

4 Standard 1" shaft trailer wheel bearings. | eBay...
Forum: Trailers & towing 25 September 2014, 18:51
Replies: 70
Views: 12,163
Posted By beamishken
Peter C please believe me uk trailers are nothing...

Peter C please believe me uk trailers are nothing like US trailers I've been changing trailer bearings 35 years & you are confusing the issue
The hubs in the link are fitted with UK standard...
Forum: Trailers & towing 25 September 2014, 16:28
Replies: 70
Views: 12,163
Posted By beamishken
Sorry but that may be correct for the hubs...

Sorry but that may be correct for the hubs currently fitted but if he uses the hubs in the link then the shaft doesn't matter as the seal is fixed to the inner race & seals on the hub.
Totally...
Forum: Trailers & towing 25 September 2014, 07:47
Replies: 70
Views: 12,163
Posted By beamishken
That is a 4" pcd hub & probably a 1" shaft so you...

That is a 4" pcd hub & probably a 1" shaft so you should be able to get standard taper bearing type hubs which are readily available & fairly cheap
You will need to check that the stub axle isn't...
Showing results 1 to 14 of 14

 


All times are GMT. The time now is 13:33.

Contact Us - RIBnet - Archive - Community Rules - Terms of Service - Privacy - Accessibility - Top

Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.