Go Back   RIBnet Forums > Search Forums
Reload this Page Search Results
Click Here to Login

Join RIBnet Today
Showing results 1 to 23 of 23
Search took 0.00 seconds. Search: Posts Made By: Jizm
Forum: Electrics and electronics 30 June 2013, 08:46
Replies: 55
Views: 22,532
Posted By Jizm
So then can some one answer this: Is it...

So then can some one answer this:

Is it possible to wire a standard gauge to the sender as well as it being connected to the smartcraft?
Forum: Electrics and electronics 16 May 2013, 07:35
Replies: 55
Views: 22,532
Posted By Jizm
Yep, the calibration is easier with the sender...

Yep, the calibration is easier with the sender out so you can move it by hand as you go. Not sure what's US and what's not but mine is a 30-240ohm and works fine....
Forum: Electrics and electronics 15 May 2013, 14:13
Replies: 55
Views: 22,532
Posted By Jizm
You don't need a proper harness for the sender....

You don't need a proper harness for the sender. Just wire the two cables to the sender using any old wire you have as a temporary test. Remove the sender and follow the calibration procedure detailed...
Forum: Electrics and electronics 15 May 2013, 08:05
Replies: 55
Views: 22,532
Posted By Jizm
Ok the black and pink and black and orange go to...

Ok the black and pink and black and orange go to your fuel sender (pink is signal). The black and blue and the other black and orange go to your external oil tank but it may not have a sender. The...
Forum: Electrics and electronics 15 May 2013, 06:43
Replies: 55
Views: 22,532
Posted By Jizm
I will lift my cowl and take a pic when I get...

I will lift my cowl and take a pic when I get home tonight...
Forum: Electrics and electronics 05 May 2013, 08:14
Replies: 55
Views: 22,532
Posted By Jizm
I'll check mine and come back on here later. It's...

I'll check mine and come back on here later. It's not too bad to do...
Forum: Electrics and electronics 16 November 2010, 14:36
Replies: 55
Views: 22,532
Posted By Jizm
Think you have to tell it a speed to read...

Think you have to tell it a speed to read from????

I.E. Paddle wheel up to say 10knots then GPS from 11knots up??

Will have a look in my manual later...
Forum: Electrics and electronics 19 October 2010, 14:24
Replies: 55
Views: 22,532
Posted By Jizm
Did it work on yours?

Did it work on yours?
Forum: Electrics and electronics 17 October 2010, 06:21
Replies: 55
Views: 22,532
Posted By Jizm
Just in case anyone else has this problem...

....on smartcraft guages with 'VDO' on them you hold '+' & '-' then switch the key on, then hold down 'MODE' for 2 seconds to enter calibration settings.
:thumbs:
Forum: Electrics and electronics 16 October 2010, 20:23
Replies: 55
Views: 22,532
Posted By Jizm
Thanks for info, will investigate...

Thanks for info, will investigate...
Forum: Electrics and electronics 16 October 2010, 20:05
Replies: 55
Views: 22,532
Posted By Jizm
So do you use a GPS connection for speed above...

So do you use a GPS connection for speed above that or just refer to your plotter?
Forum: Electrics and electronics 16 October 2010, 18:40
Replies: 55
Views: 22,532
Posted By Jizm
Ahh, wrong PDF. this is the one I should be...

Ahh, wrong PDF.
this is the one I should be referring to:

https://download.brunswick-marine.com/filereader/file/pdf/4/enen/smartcraft/2003/10229021.pdf
Forum: Electrics and electronics 16 October 2010, 11:03
Replies: 55
Views: 22,532
Posted By Jizm
OK I'm following the manual, holding 'MODE' and...

OK I'm following the manual, holding 'MODE' and '+' but not getting into CAL1, get to the time on the speedo but no further, what am I doing wrong?:]
Forum: Electrics and electronics 08 October 2010, 16:47
Replies: 55
Views: 22,532
Posted By Jizm
Like these I have just found cut off under the...

Like these I have just found cut off under the cowl perhaps?
Forum: Electrics and electronics 29 September 2010, 05:49
Replies: 55
Views: 22,532
Posted By Jizm
I am strarting to agree, may just fit a standard...

I am strarting to agree, may just fit a standard fuel guage at this rate....:rolleyes:
Forum: Electrics and electronics 28 September 2010, 09:01
Replies: 55
Views: 22,532
Posted By Jizm
:thumbs: cheers for that... could see any...

:thumbs: cheers for that...
could see any refernce to the connection on the first link though?:]
Forum: Electrics and electronics 27 September 2010, 19:17
Replies: 55
Views: 22,532
Posted By Jizm
OK, thanks. Getting dark now...

OK, thanks. Getting dark now...
Forum: Electrics and electronics 27 September 2010, 18:50
Replies: 55
Views: 22,532
Posted By Jizm
The guages are version 2.80 and now I am...

The guages are version 2.80 and now I am scrolling through they do not display fuel level. Which guage usually displays fuel level, speedo or tacho?
Forum: Electrics and electronics 27 September 2010, 17:55
Replies: 55
Views: 22,532
Posted By Jizm
ok mine reads 2.4Kohms!!!!!

ok mine reads 2.4Kohms!!!!!
Forum: Electrics and electronics 27 September 2010, 14:31
Replies: 55
Views: 22,532
Posted By Jizm
normal is about 30-250ish ohms so whats a US one?

normal is about 30-250ish ohms so whats a US one?
Forum: Electrics and electronics 27 September 2010, 11:45
Replies: 55
Views: 22,532
Posted By Jizm
Ah, thanks that concurs with the link from...

Ah, thanks that concurs with the link from Martini! Standard analogue signal from the sender I take it?
Jiz
Forum: Electrics and electronics 27 September 2010, 05:31
Replies: 55
Views: 22,532
Posted By Jizm
Thanks for that, just need to find the fuel...

Thanks for that, just need to find the fuel sender as I have the oil tank and the paddle wheel, and go from there.
Forum: Electrics and electronics 26 September 2010, 18:58
Replies: 55
Views: 22,532
Posted By Jizm
Smart craft fuel display

Another question,
does anyone know how a fuel sender connects into the smartcraft guages? Wire colours etc? Googled it but no joy. Trying to find a schematic, the display shows fuel but can't see...
Showing results 1 to 23 of 23

 


All times are GMT. The time now is 20:45.

Contact Us - RIBnet - Archive - Community Rules - Terms of Service - Privacy - Accessibility - Top

Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.