Forum: Engines & props
26 March 2015, 11:35
|
Replies: 47
Views: 11,374
I'm still waiting on the gasket but swapped the...
I'm still waiting on the gasket but swapped the float valve to that from the equivalent Mariner carb (the pin is a bit thicker and machined vs a simple thin pin) - it started on the briefest touch of...
|
Forum: Engines & props
07 March 2015, 12:29
|
Replies: 47
Views: 11,374
|
Forum: Engines & props
06 March 2015, 19:09
|
Replies: 47
Views: 11,374
|
Forum: Engines & props
06 March 2015, 15:56
|
Replies: 47
Views: 11,374
|
Forum: Engines & props
28 February 2015, 10:13
|
Replies: 47
Views: 11,374
So it does!
A bit of Googling showed the...
So it does!
A bit of Googling showed the float level to be 18 ± 0.5 mm which turns out to be 'level'. The actual float valve had a bit of stiction in it. Even though it would have fuel pressure...
|
Forum: Engines & props
27 February 2015, 16:53
|
Replies: 47
Views: 11,374
|
Forum: Engines & props
26 February 2015, 07:30
|
Replies: 47
Views: 11,374
|
Forum: Engines & props
25 February 2015, 11:30
|
Replies: 47
Views: 11,374
|
Forum: Engines & props
25 February 2015, 07:23
|
Replies: 47
Views: 11,374
When I was about sixteen a friend gave a couple...
When I was about sixteen a friend gave a couple of us a lift home from school in a (by that time very old) Vanden Plas Allegro. Trying to impress us he took a hump-back bridge at some speed and the...
|
Forum: Engines & props
25 February 2015, 06:44
|
Replies: 47
Views: 11,374
|
Forum: Engines & props
24 February 2015, 21:32
|
Replies: 47
Views: 11,374
Thanks,
1) The thermostat got blocked with a...
Thanks,
1) The thermostat got blocked with a bit of impeller and it slowed to a dignified halt. After cooling it restarted but then slowed to a halt again. The pistons were scuffed and there was...
|
Forum: Engines & props
24 February 2015, 20:23
|
Replies: 47
Views: 11,374
|
Forum: Engines & props
23 February 2015, 06:52
|
Replies: 47
Views: 11,374
Thanks All,
It doesn't have one of those...
Thanks All,
It doesn't have one of those levers.
It is approx 1991.
I have a workshop manual but can't find the flippin' thing! :(
I'll run another compression test and report back.
I...
|
Forum: Engines & props
21 February 2015, 20:32
|
Replies: 47
Views: 11,374
When I prime it I can hear fuel going into the...
When I prime it I can hear fuel going into the carb - up to the point that the bulb goes hard (the float has closed off the fuel to the bowl).
Tomorrow I'll try and start it with someone pumping...
|
Forum: Engines & props
21 February 2015, 16:39
|
Replies: 47
Views: 11,374
Poor starting - Yamaha 30 2S, 2 Cyl
Hi,
I have an early 90's Yamaha 30 (the same '689' engine they made for Mariner).
It eventually starts if I open the throttle, close the choke and wind it over for about a minute (in ten second...
|