Forum: RIBs & ribbing
09 December 2008, 08:33
|
Replies: 10
Views: 1,837
|
Forum: RIBs & ribbing
08 December 2008, 13:50
|
Replies: 10
Views: 1,837
|
Forum: Upcoming RIB cruises
03 December 2008, 13:25
|
Replies: 112
Views: 17,056
|
Forum: RIBs & ribbing
28 July 2008, 08:57
|
Replies: 11
Views: 2,761
|
Forum: RIBs & ribbing
14 July 2008, 12:30
|
Replies: 7
Views: 1,067
|
Forum: RIBs & ribbing
11 July 2008, 19:31
|
Replies: 4
Views: 1,248
There is not a lot of choice at low tide.
I...
There is not a lot of choice at low tide.
I would go for a picnic at East Head, if I were you.
Also, depending on the age of the family, you could try going up Emsworth channel to see if you can...
|
Forum: RIBs & ribbing
03 July 2008, 16:24
|
Replies: 9
Views: 1,563
Thanks Cookie
Thats just what I wanted to...
Thanks Cookie
Thats just what I wanted to know.
I hate (cleaning) paint rollers and I guess I am going to get to hate resin rollers.
Its just that for large flat areas a brush will be too...
|
Forum: RIBs & ribbing
27 June 2008, 17:09
|
Replies: 9
Views: 1,563
Hi Martini
I supose I should have asked you...
Hi Martini
I supose I should have asked you straight away, seeing as you have just done about twice the area.
I bought some CFS rollers too. It just seems a bit of a shame to bin them every...
|
Forum: RIBs & ribbing
27 June 2008, 10:36
|
Replies: 9
Views: 1,563
|
Forum: RIBs & ribbing
27 June 2008, 09:50
|
Replies: 9
Views: 1,563
Laminating GRP
Because I am a tight git, I would like to re-use my resin rollers when I laminate in my new deck. :(
What is the best method of cleaning resin rollers?
Is it really worth while or should I just bin...
|
Forum: RIBs & ribbing
25 June 2008, 15:29
|
Replies: 12
Views: 2,703
It has saved me some fuel. :D
The hard part...
It has saved me some fuel. :D
The hard part is knowing where to stop. I keep finding bits that may need replacing, so I rip them out.
Once clean and rot free it is (I hope) just a matter of...
|
Forum: Electrics and electronics
25 June 2008, 09:42
|
Replies: 7
Views: 1,455
|
Forum: RIBs & ribbing
25 June 2008, 09:36
|
Replies: 12
Views: 2,703
|
Forum: RIBs & ribbing
25 June 2008, 09:33
|
Replies: 42
Views: 8,575
|
Forum: RIBs & ribbing
25 June 2008, 09:24
|
Replies: 5
Views: 1,313
Bruce
I will get some stick for this but....
...
Bruce
I will get some stick for this but....
Use some ordinary WBP (exterior grade) ply. A whole sheet will cost less than a 1/4 sheet of the marine stuff. Hopefully your seat base will not be...
|
Forum: RIBs & ribbing
24 June 2008, 11:54
|
Replies: 10
Views: 2,098
Hi Shirehorse.
Don't start stripping your...
Hi Shirehorse.
Don't start stripping your unit down. You will have springs and ball bearing all over the shop in seconds.
Strictly speaking the pump is not a pump and should be known as a...
|
Forum: RIBs & ribbing
20 June 2008, 15:39
|
Replies: 42
Views: 8,575
Keith
Thanks for that.
It is a very similar...
Keith
Thanks for that.
It is a very similar arangement to mine. It even looks like the same top hat moulding. :eek:
I think Bruce is right about it being too far aft, but if I bring the whole...
|
Forum: RIBs & ribbing
20 June 2008, 12:43
|
Replies: 5
Views: 1,313
|
Forum: RIBs & ribbing
20 June 2008, 07:30
|
Replies: 42
Views: 8,575
|
Forum: RIBs & ribbing
19 June 2008, 12:28
|
Replies: 42
Views: 8,575
Bruce
Your trunk is more or less how things...
Bruce
Your trunk is more or less how things were before it all went rotten. There is a photo of the old arangement further back.
I am trying to find a way of smoothing out the throttle and gear...
|
Forum: RIBs & ribbing
19 June 2008, 11:02
|
Replies: 42
Views: 8,575
|
Forum: RIBs & ribbing
19 June 2008, 10:13
|
Replies: 42
Views: 8,575
A solution pehaps?
I was looking at a mates...
A solution pehaps?
I was looking at a mates Ribtec 655 yesterday, and I may have an answer.
He has a bit of rectangular trunking (extractor duct) on the underside of the deck from the front...
|
Forum: RIBs & ribbing
17 June 2008, 10:17
|
Replies: 42
Views: 8,575
|
Forum: RIBs & ribbing
17 June 2008, 10:07
|
Replies: 42
Views: 8,575
|
Forum: RIBs & ribbing
17 June 2008, 09:24
|
Replies: 42
Views: 8,575
Thanks Guys.
Lots of good ideas and allready...
Thanks Guys.
Lots of good ideas and allready some controversy.
It is just the engine control cables that I am considering. The electrical stuff is easy. There is very little under deck space...
|