Forum: Electrics and electronics
16 June 2013, 00:44
|
|
Replies: 12
Views: 5,084
Navicom mmsi reste
Hi, i have a navicom 450 vhf from an old boat. i need to put it in my new boat. How can i reset the mmsi ?
Thanks
|
|
Forum: Engines & props
22 August 2012, 10:13
|
|
Replies: 0
Views: 1,363
BF90A internal anodes
Hi,
can you help me identify the internal anodes in a 2002 BF90A? I suspect that I have 2, one on the exhaustion and another in the water jacket.
Is that correct?
Can you put 1 or 2 photos...
|
|
Forum: Engines & props
15 March 2012, 23:07
|
|
Replies: 9
Views: 2,016
Hi,
thanks to all. I bought a Honda fuel...
Hi,
thanks to all. I bought a Honda fuel filter that is similar to the Racor filters. The outboard goes fine without the old CAV filter. I'm going to try with this new filter and then I'll let you...
|
|
Forum: Engines & props
14 March 2012, 14:36
|
|
Replies: 9
Views: 2,016
|
|
Forum: Engines & props
14 March 2012, 14:31
|
|
Replies: 9
Views: 2,016
|
|
Forum: Engines & props
14 March 2012, 12:10
|
|
Replies: 9
Views: 2,016
bf90 stalls at 4000rpm after a while
Hi,
I have a Honda BF90A2 that after sometime running at 4000rpm stops with fuel starvation. The primer bulb is colapsed. Normally it starts right away and does the same problem after a while. The...
|
|
Forum: Engines & props
02 November 2011, 17:15
|
|
Replies: 3
Views: 1,477
|
|
Forum: Engines & props
02 November 2011, 16:14
|
|
Replies: 3
Views: 1,477
Zerk fittings
Hi,
i have a Honda BF90A and I need to know what type of grease should I use in the zerk fittings of my outboard. In the market I see marine greases with teflon and without it.
Can I use a...
|
|
Forum: Engines & props
27 September 2011, 21:03
|
|
Replies: 9
Views: 4,363
|
|
Forum: Engines & props
27 September 2011, 14:22
|
|
Replies: 9
Views: 4,363
Hi,
updated information. Carbs cleaned and...
Hi,
updated information. Carbs cleaned and synced. Thermostat wasn't very good but is already repaired. The problem persists.
The spark plugs and fuel filter were also changed.
Could it be...
|
|
Forum: Engines & props
26 September 2011, 22:29
|
|
Replies: 9
Views: 4,363
|
|
Forum: Engines & props
26 September 2011, 22:07
|
|
Replies: 9
Views: 4,363
|
|
Forum: Engines & props
26 September 2011, 19:16
|
|
Replies: 9
Views: 4,363
BF50 stalls
Hi,
a friend of mine has a 2006 Honda BF50 which stalls when putting the throtle to wide-open starting from being neutral.
Looking at the prime bulb, it is like not having gas at all in it. If we...
|
|
Forum: Engines & props
06 September 2011, 09:23
|
|
Replies: 7
Views: 1,567
|
|
Forum: Engines & props
05 September 2011, 16:55
|
|
Replies: 7
Views: 1,567
|
|
Forum: Engines & props
05 September 2011, 01:16
|
|
Replies: 7
Views: 1,567
Tell-tale tube
Hi everyone,
today while testing a honda bf90 the tell-tale tube came out of place and saltwater went inside the outboard. The trim stopped working. After detecting the problem, I washed the...
|
|
Forum: Engines & props
28 May 2011, 00:50
|
|
Replies: 10
Views: 6,430
|
|
Forum: Engines & props
27 May 2011, 13:44
|
|
Replies: 10
Views: 6,430
Hi again,
I've noticed that if I giggle my...
Hi again,
I've noticed that if I giggle my outboard my steering wheel doesn't turn imediatlly. It has some looseness. How can I tighten the steering cable in the wheel so that the looseness is...
|
|
Forum: Engines & props
27 May 2011, 13:41
|
|
Replies: 10
Views: 6,430
|
|
Forum: Engines & props
27 May 2011, 01:08
|
|
Replies: 10
Views: 6,430
|
|
Forum: Engines & props
19 May 2011, 13:01
|
|
Replies: 10
Views: 6,430
Honda BF50 control cable
Hi,
I have to replace the shift control cable in a Honda BF50A outboard. Can someone explain me how to take the cable out in the outboard side? The cable goes in the outboard but I don't know how...
|
