Forum: RIBs & ribbing
25 August 2022, 19:44
|
Replies: 9
Views: 960
Blue lagoon ( not the film)
No problem. PM sent with the details.
As per passage the tide is a bit weird round these parts and tends to continue flooding up to two hours after HW, same on the ebb. So slack water is about two...
|
Forum: RIBs & ribbing
25 August 2022, 10:58
|
Replies: 9
Views: 960
You can launch at porthclais around 2-3 hours...
You can launch at porthclais around 2-3 hours either side of high water easily and lower if you are prepared to drive and launch over gravel and sand. It is a nice trip round from porthclais to the...
|
Forum: Engines & props
05 May 2021, 07:57
|
Replies: 0
Views: 265
Breaking a Yamaha 50D with ptt
As a follow on from a previous post I am going to break up my Yamaha 50D (3 cylinder, 2 stroke) for parts.
Either the top bearing or the middle cylinder is goosed and it’s seized. I don’t want to...
|
Forum: Engines & props
29 April 2021, 10:25
|
Replies: 0
Views: 509
Yamaha F40 or F50
I am looking for a used Yamaha F40 or F50 (prefer the fuel injection one) or similar if anyone knows where a decent one is for sale?
|
Forum: RIBs & ribbing
08 September 2019, 06:19
|
Replies: 1
Views: 771
|
Forum: Engines & props
20 May 2019, 19:03
|
Replies: 2
Views: 663
It isn’t a silly question!
My Yamaha...
It isn’t a silly question!
My Yamaha doesn’t, but it does have a box the covers the front of the carbs and the air does have to go around a few corners to get into the carbs!
From memory I...
|
Forum: RIBs & ribbing
30 March 2019, 08:45
|
Replies: 2
Views: 712
|
Forum: RIBs & ribbing
20 February 2019, 07:52
|
Replies: 26
Views: 8,948
|
Forum: RIBs & ribbing
04 November 2018, 10:01
|
Replies: 24
Views: 4,846
Avon sr4 of unknown vintage
I get the op’s point, the sr deck is totally flat so even a small amount of water washes about and comes forward when you back off the throttle but I don’t think cutting the deck is the answer, an...
|
Forum: RIBs & ribbing
03 November 2018, 22:50
|
Replies: 24
Views: 4,846
Avon sr4 of unknown vintage
I think a lot depends on what outboard you are going to put on the back, if you are going for a 40 or 50 I would be concerned that force and weight of the motor would break the join between the deck...
|
Forum: RIBs & ribbing
03 November 2018, 21:57
|
Replies: 24
Views: 4,846
Avon sr4 of unknown vintage
I would say from the logo it’s an old one!! I have the same logos on mine and it’s serial number predates the newer serial numbers where the last two digits represents the year of manufacture. Do you...
|
Forum: RIBs & ribbing
23 October 2018, 09:41
|
Replies: 15
Views: 1,463
Does anyone what the full list of boats that...
Does anyone what the full list of boats that entered the challenge was?
It looks like a couple of 4.8 Ribcrafts, an SR4, the Gemini, a Humber something and a red one that I think might be a Delta?
|
Forum: RIBs & ribbing
19 October 2018, 21:38
|
Replies: 15
Views: 1,463
|
Forum: Electrics and electronics
01 October 2018, 20:12
|
Replies: 9
Views: 21,739
|
Forum: Electrics and electronics
30 September 2018, 19:10
|
Replies: 9
Views: 21,739
Thanks all, Boris the second image is pretty...
Thanks all, Boris the second image is pretty close to what I have but I can’t find where to connect the oil harness engine end? I have tried searching the internet for an adapter but so far have...
|
Forum: Engines & props
29 September 2018, 20:37
|
Replies: 3
Views: 703
|
Forum: Electrics and electronics
28 September 2018, 12:15
|
Replies: 9
Views: 21,739
Here is the trim wiring harness, two of the...
Here is the trim wiring harness, two of the bullet connectors have come off but before they came off the wires matched four wires from the sender.
127038
The plug the gauge end matches a plug ...
|
Forum: Electrics and electronics
28 September 2018, 08:05
|
Replies: 9
Views: 21,739
Yamaha trim sender wiring
I am hoping I can pick the collective brains of the forum regarding some old Yamaha electronics.
I have an old (1989) Yamaha 50DETO and as part of my winter work I am trying to hook up a...
|
Forum: Electrics and electronics
19 August 2018, 21:54
|
Replies: 5
Views: 1,632
|
Forum: Electrics and electronics
18 August 2018, 20:11
|
Replies: 5
Views: 1,632
Sorry to revive an old thread but as part of my...
Sorry to revive an old thread but as part of my outboard overhaul I am going to try and get this sorted. A massive thanks to Davie for sending me the parts to fix the broken lower mounts from another...
|
Forum: Electrics and electronics
01 December 2016, 14:16
|
Replies: 5
Views: 1,632
|
Forum: Electrics and electronics
01 December 2016, 09:09
|
Replies: 5
Views: 1,632
Yamaha trim sender query
I have been searching the internet to try and solve this but I think I might be even more confused!!!
I have an old yam 50 (DETO) and there is a trim sender on the bracket. I would like to hook...
|
Forum: RIBs & ribbing
06 November 2016, 19:54
|
Replies: 38
Views: 5,367
70hp on an Avon SR4?
Hi Alex,
Was that the boat that was on eBay?
I don't know the weight of your 70 but I had a yam 55 on mine for a couple of years and with everything heavy forward it was pretty well balanced...
|
Forum: Engines & props
23 October 2016, 11:43
|
Replies: 12
Views: 1,872
|
Forum: Engines & props
23 October 2016, 10:36
|
Replies: 12
Views: 1,872
Hi Davie.
Tell me more [emoji2]
I...
Hi Davie.
Tell me more [emoji2]
I believe you are in Scotland and I am in west Wales, but as luck would have it my wife is in Stirling until Thursday!!!!! Is this anywhere near where you are?
...
|