Forum: Electrics and electronics
16 April 2020, 17:02
|
Replies: 5
Views: 791
|
Forum: Electrics and electronics
15 April 2020, 16:31
|
Replies: 5
Views: 791
OK, noted thanks. Here a wiring diagram, the...
OK, noted thanks. Here a wiring diagram, the possible problem is marked with red, the "SEN" terminal. Not an electrician(probably clear for all at this stage :) ) but it looks like there is a direct...
|
Forum: Electrics and electronics
15 April 2020, 10:39
|
Replies: 5
Views: 791
|
Forum: Electrics and electronics
15 April 2020, 09:17
|
Replies: 5
Views: 791
Alternator problem, help needed...
Not rib but marine engine related...would highly appreciate if anyone here that knows alternators would give a helping advice? Long story but during tracing a ground leak found that the voltage sense...
|
Forum: Inflatable boats - SIBs and folding RIBs
03 April 2020, 19:15
|
Replies: 9
Views: 1,384
Done exactly that ones...i know exactly how it...
Done exactly that ones...i know exactly how it feels! Still can feel the walk of shame.... The bow went high and really lucky that the fin of the yamaha 90 did not touch the concrete...no major...
|
Forum: RIBs & ribbing
28 March 2020, 20:25
|
Replies: 0
Views: 576
Early start of season?
South Finland was yesterday isolated from rest of the country(can not cross the "border" unless essential biz, all rods in and out are monitored). Within, you can still move freely but obviously...
|
Forum: Upcoming RIB cruises
10 December 2019, 19:27
|
Replies: 49
Views: 5,465
As mentioned a drogue anchor is good to have....
As mentioned a drogue anchor is good to have. Consider also the fueling how it will be done in possible high seas. If the weather will turn bad, You might want to have more fuel reserve than 110L for...
|
Forum: RIBs & ribbing
10 December 2019, 19:07
|
Replies: 8
Views: 1,038
Impact absorbing cushions ?
So far my old spine has not been complaining too much about sudden hits but guess its only a matter of time, sometimes the G forces must be tremendous....
How about this material :
...
|
Forum: RIBs & ribbing
07 December 2019, 08:29
|
Replies: 26
Views: 4,030
|
Forum: RIBs & ribbing
06 December 2019, 15:46
|
Replies: 26
Views: 4,030
|
Forum: RIB gallery
26 October 2019, 06:09
|
Replies: 478
Views: 216,299
My SR is still going strong after all these...
My SR is still going strong after all these years! Picture from the archipelago sea. Best part was to drive there and back, 110 nautical miles one way, 6-7 hours driving including one fueling &...
|
Forum: RIBs & ribbing
28 August 2019, 15:35
|
Replies: 8
Views: 1,505
|
Forum: Engines & props
25 August 2019, 19:47
|
Replies: 18
Views: 2,171
|
Forum: RIBs & ribbing
24 August 2019, 21:10
|
Replies: 50
Views: 9,498
|
Forum: RIBs & ribbing
24 August 2019, 20:08
|
Replies: 50
Views: 9,498
|
Forum: RIBs & ribbing
31 January 2019, 20:00
|
Replies: 4
Views: 829
Hempel's Light Primer 45551 or equivalent works...
Hempel's Light Primer 45551 or equivalent works well as primer also on epoxy, think it is available also in 0,375 tins. Can be finished with various top coats. Not easy to get a smooth finish but can...
|
Forum: Inflatable boats - SIBs and folding RIBs
20 September 2018, 20:40
|
Replies: 9
Views: 5,515
You see basically the the same outboard as...
You see basically the the same outboard as johnsson, evinrude, tohatsu, mercury as the Marinen 3.3 . Hp range from 2.5 - 3.5. Power head all the same, small difference in carb between the HP. The...
|
Forum: Inflatable boats - SIBs and folding RIBs
11 September 2018, 08:00
|
Replies: 12
Views: 3,264
If the plate is original, probably a 1994 or...
If the plate is original, probably a 1994 or later. On the plate there is the text "directive 94/25/CE " That directive is dated 16.06.1994 so the plate is probably older than that. Maybe the...
|
Forum: Engines & props
14 August 2018, 18:56
|
Replies: 8
Views: 1,088
|
Forum: Engines & props
12 August 2018, 07:44
|
Replies: 68
Views: 14,887
|
Forum: RIBs & ribbing
08 August 2018, 12:29
|
Replies: 107
Views: 26,722
|
Forum: RIBs & ribbing
08 August 2018, 10:42
|
Replies: 107
Views: 26,722
He wants 3500 for the hull, the problem is the...
He wants 3500 for the hull, the problem is the potential amount of work. The strakes on the tubes alone need plenty of work, transom was maybe not weak yet but had water damages as had already some...
|
Forum: RIBs & ribbing
08 August 2018, 06:54
|
Replies: 107
Views: 26,722
Hi Stresspill.
Went to check the boat You...
Hi Stresspill.
Went to check the boat You posted https://www.rib.net/forum/f21/sr6-for-sale-in-finland-79519.html
Think the tubes are in much worse condition than yours, plenty of work even if...
|
Forum: RIBs & ribbing
30 October 2017, 20:35
|
Replies: 21
Views: 5,946
Not 100 % sure but can not see an outboard or...
Not 100 % sure but can not see an outboard or even sterndrive? If it is an inboard, then trimming up possibilities is rather limited. In any case it looked bow heavy, maybe used a water ballast tank...
|
Forum: RIBs & ribbing
04 October 2017, 16:24
|
Replies: 1
Views: 1,418
|