Forum: Engines & props
30 July 2013, 17:50
|
Replies: 1
Views: 1,473
Thermostat
Just taken my thermostat housing off, the two gaskets seem to have had something very sticky put on them, it was done at a local service centre two years ago. Is this normal ? Just ordered new...
|
Forum: Engines & props
28 July 2013, 20:31
|
Replies: 10
Views: 2,341
|
Forum: Engines & props
28 July 2013, 20:25
|
Replies: 10
Views: 2,341
|
Forum: Engines & props
26 July 2013, 20:30
|
Replies: 10
Views: 2,341
|
Forum: Engines & props
26 July 2013, 12:50
|
Replies: 10
Views: 2,341
Cooling System
Hi all,
Is there a simple way of checking that the cooling system is ok on my 50hp, 2 cylinder, 2 stroke outboard. The pee hole is clear and seems to pump water well, but I have been told that...
|
Forum: Engines & props
09 July 2013, 16:39
|
Replies: 18
Views: 2,532
|
Forum: Engines & props
09 July 2013, 14:47
|
Replies: 18
Views: 2,532
|
Forum: Engines & props
08 July 2013, 04:41
|
Replies: 18
Views: 2,532
|
Forum: Engines & props
07 July 2013, 18:01
|
Replies: 18
Views: 2,532
|
Forum: Engines & props
07 July 2013, 18:00
|
Replies: 18
Views: 2,532
|
Forum: Engines & props
07 July 2013, 17:59
|
Replies: 18
Views: 2,532
|
Forum: Engines & props
07 July 2013, 17:58
|
Replies: 18
Views: 2,532
|
Forum: Engines & props
07 July 2013, 15:32
|
Replies: 18
Views: 2,532
|
Forum: Engines & props
07 July 2013, 12:33
|
Replies: 18
Views: 2,532
Loss of power
Help needed please.....
Had the boat out yesterday and today, I had the same problem both days.
The engine starts on the button, ticks over fine, I run it at about 4000rpm for 30 minutes then it...
|
Forum: RIBs & ribbing
20 August 2012, 16:42
|
Replies: 3
Views: 1,160
|
Forum: RIBs & ribbing
18 August 2012, 15:32
|
Replies: 3
Views: 1,160
poole moorings
Hi all,
Going to Poole for a few days camping and wanting to take the rib, any recommendations where I might be able to stick the boat in and leave it in for a few days at short notice??
|
Forum: RIBs & ribbing
13 August 2012, 21:15
|
Replies: 16
Views: 2,036
|
Forum: RIBs & ribbing
13 August 2012, 21:10
|
Replies: 16
Views: 2,036
|
Forum: RIBs & ribbing
13 August 2012, 20:52
|
Replies: 16
Views: 2,036
|
Forum: RIBs & ribbing
13 August 2012, 20:51
|
Replies: 16
Views: 2,036
|
Forum: RIBs & ribbing
13 August 2012, 16:51
|
Replies: 16
Views: 2,036
|
Forum: RIBs & ribbing
13 August 2012, 16:24
|
Replies: 16
Views: 2,036
Ok done this and found the leak....
Its on a...
Ok done this and found the leak....
Its on a seam at the rear of the tube on the underside, about 10mm of the overlap has started to come away and its slowly leaking from it.
Can I glue a strip of...
|
Forum: RIBs & ribbing
12 August 2012, 15:43
|
Replies: 16
Views: 2,036
|
Forum: RIBs & ribbing
12 August 2012, 15:01
|
Replies: 16
Views: 2,036
tube going down !!!
I have a section of tube which has started to slowly de-flate, there are no signs of damage
any where.
Whats the easiest way to find a leak, maybe its the valve letting by ???
Thanks
|
Forum: RIBs & ribbing
02 September 2011, 20:37
|
Replies: 23
Views: 11,514
|