Forum: RIBs & ribbing
16 September 2013, 20:16
|
Replies: 105
Views: 17,188
|
Forum: RIBs & ribbing
12 July 2012, 11:43
|
Replies: 18
Views: 3,277
Made the most of a break in the weather last...
Made the most of a break in the weather last Friday and launched from Mylor. Here is a couple of stills from the Gopro video just to prove Mylor is not always a nightmare. One showing the slip the...
|
Forum: RIBs & ribbing
08 July 2012, 18:19
|
Replies: 18
Views: 3,277
We do the same if possible. Which highlights...
We do the same if possible. Which highlights another problem, when I have parked up in the valley I bought a ticket for the trailer from the attendant by the slip. If you launch at 6am where do you...
|
Forum: RIBs & ribbing
08 July 2012, 17:08
|
Replies: 18
Views: 3,277
|
Forum: RIBs & ribbing
08 July 2012, 12:02
|
Replies: 18
Views: 3,277
|
Forum: RIBs & ribbing
14 March 2012, 22:16
|
Replies: 3
Views: 1,270
|
Forum: RIBs & ribbing
01 February 2012, 06:05
|
Replies: 11
Views: 4,107
|
Forum: RIBs & ribbing
11 January 2012, 07:50
|
Replies: 107
Views: 21,297
Hi
Has anyone had seen a new edition of the...
Hi
Has anyone had seen a new edition of the magazine? I heard it was going to be out before the start of the boat show but I've not seen anything.
Want to reserve judgment on the changes till...
|
Forum: RIBs & ribbing
10 January 2012, 07:09
|
Replies: 29
Views: 3,953
Can't wait for the Pandora to open again. The...
Can't wait for the Pandora to open again. The Smugglers has been a farce all summer long! The Tregothnan estate seem to employ there staff on looks alone!
Mylor's a good slip to launch from...
|
Forum: Commercial operators
07 January 2012, 07:10
|
Replies: 28
Views: 6,416
|
Forum: RIBs & ribbing
31 December 2011, 17:30
|
Replies: 25
Views: 3,259
|
Forum: RIBs & ribbing
31 December 2011, 17:08
|
Replies: 25
Views: 3,259
|
Forum: RIBs & ribbing
31 December 2011, 06:45
|
Replies: 25
Views: 3,259
Hi Nathan,
The compression tester I've got...
Hi Nathan,
The compression tester I've got came from a bike shop called Hein Gericke. It came with two adapters and two universal adapters, which are rubber cones that you have to push into the...
|
Forum: Engines & props
30 December 2011, 12:35
|
Replies: 6
Views: 12,232
|
Forum: Engines & props
30 December 2011, 11:49
|
Replies: 6
Views: 12,232
Compression psi for a Yam 50hp
Hi dose anyone know the ballpark compression a Yamaha 50hp 2 stroke should produce? I think it's a 1985 engine.
I need to re do the test because I didn't have the throttle wide open. But I can't...
|
Forum: Inflatable boats - SIBs and folding RIBs
17 December 2011, 07:00
|
Replies: 8
Views: 1,546
|
Forum: Inflatable boats - SIBs and folding RIBs
17 December 2011, 06:51
|
Replies: 8
Views: 1,546
Good video! Must of been a pretty consistent...
Good video! Must of been a pretty consistent break to allow you to get those shot, some looked like you were pretty close to getting caught inside. I'm always amazed when I watch videos of Teahupoo...
|
Forum: Commercial operators
15 December 2011, 14:19
|
Replies: 15
Views: 3,939
|
Forum: Commercial operators
15 December 2011, 11:28
|
Replies: 15
Views: 3,939
Hi Chris what endorsement did you get in the...
Hi Chris what endorsement did you get in the end? and do you know what are the other endorsements that can be issued?
I've just done my ML5 and had a problem with the Ishihara plate test....
|
Forum: RIBs & ribbing
04 December 2011, 08:02
|
Replies: 2
Views: 1,721
|
Forum: RIBs & ribbing
03 December 2011, 18:11
|
Replies: 11
Views: 3,004
|
Forum: Engines & props
28 November 2011, 17:52
|
Replies: 3
Views: 5,111
|
Forum: Engines & props
28 November 2011, 11:48
|
Replies: 3
Views: 5,111
|
Forum: Engines & props
25 November 2011, 18:41
|
Replies: 3
Views: 5,111
Yamaha year code M?
Hi,
I was reading through thread on here a couple of days ago and a topic of Yamaha engine model codes came up. I found a Chart which shows what year the outboard was made by using the last letter...
|
Forum: RIBs & ribbing
20 November 2011, 18:18
|
Replies: 4
Views: 1,725
|