Forum: Electrics and electronics
13 June 2010, 16:30
|
Replies: 7
Views: 1,713
|
Forum: Electrics and electronics
05 February 2010, 19:35
|
Replies: 14
Views: 3,456
|
Forum: Electrics and electronics
29 January 2010, 22:35
|
Replies: 14
Views: 3,456
|
Forum: Electrics and electronics
29 January 2010, 22:25
|
Replies: 13
Views: 3,325
|
Forum: Electrics and electronics
06 January 2010, 20:28
|
Replies: 21
Views: 4,430
Make a sketch of how you have it all...
Make a sketch of how you have it all connected,you should have a central backbone with a termination at each end and power fed in somewhere at one of the "t" joints. Then all your instruments and...
|
Forum: Electrics and electronics
25 November 2009, 19:23
|
Replies: 20
Views: 11,945
If you solder and heatshrink all the wires,...
If you solder and heatshrink all the wires, making sure you connect both the inner and outer of the screened cables then overwrap the lot with self amalgamating tape then you should be fine.
No...
|
Forum: Electrics and electronics
25 October 2009, 21:13
|
Replies: 12
Views: 2,738
|
Forum: Electrics and electronics
17 October 2009, 19:25
|
Replies: 25
Views: 4,445
|
Forum: Electrics and electronics
17 October 2009, 19:20
|
Replies: 12
Views: 4,423
Just sorted this on a customers boat, the GPS...
Just sorted this on a customers boat, the GPS antenna has old software in it and needs to be updated via whatever method your specific Garmin does it by. I saw the fault showing as a duff date/time...
|
Forum: Electrics and electronics
17 October 2009, 19:18
|
Replies: 9
Views: 1,760
|
Forum: Electrics and electronics
27 September 2009, 22:57
|
Replies: 12
Views: 4,423
|
Forum: Electrics and electronics
08 September 2009, 19:13
|
Replies: 12
Views: 6,165
|
Forum: Inflatable boats - SIBs and folding RIBs
26 June 2009, 20:24
|
Replies: 5
Views: 1,809
|
Forum: Other stuff
21 June 2009, 20:47
|
Replies: 7
Views: 6,197
|
Forum: Inflatable boats - SIBs and folding RIBs
21 June 2009, 20:45
|
Replies: 1
Views: 1,219
|
Forum: Inflatable boats - SIBs and folding RIBs
18 June 2009, 07:03
|
Replies: 10
Views: 3,077
|
Forum: RIB gallery
17 June 2009, 17:16
|
Replies: 17
Views: 3,096
|
Forum: RIBs & ribbing
17 June 2009, 17:09
|
Replies: 2
Views: 1,265
|
Forum: Electrics and electronics
15 June 2009, 20:25
|
Replies: 7
Views: 1,725
|
Forum: Trailers & towing
13 June 2009, 09:06
|
Replies: 7
Views: 2,359
I use these guys for bearings for work...
I use these guys for bearings for work www.bearing-king.co.uk they often have bearings that others cannot get hold of, not sure how the prices stack up against ebay etc, but might be worth a look.
|
Forum: Electrics and electronics
09 June 2009, 18:14
|
Replies: 6
Views: 2,403
|
Forum: Electrics and electronics
08 June 2009, 19:09
|
Replies: 10
Views: 2,796
|
Forum: Tow vehicles, 4x4s, trucks, cars & bikes
07 June 2009, 19:38
|
Replies: 19
Views: 4,857
I had water in the one of the sensor wire just...
I had water in the one of the sensor wire just behind the grille (drivers side) on my navara and had the same problem, once it dried out all was sorted. I had jetwashed the vehicle the evening before.
|
Forum: Electrics and electronics
04 June 2009, 20:58
|
Replies: 15
Views: 2,825
|
Forum: RIBs & ribbing
04 June 2009, 20:54
|
Replies: 21
Views: 3,847
|