Forum: Trailers & towing
08 September 2008, 13:03
|
Replies: 29
Views: 6,190
|
Forum: RIBs & ribbing
18 November 2006, 07:58
|
Replies: 37
Views: 6,229
allthough pumps when running do use a lot of...
allthough pumps when running do use a lot of current the actule time spent working is small so the solor panel does charge it up again. This will be the third year my 8m will be in the water with...
|
Forum: RIBs & ribbing
15 November 2006, 16:32
|
Replies: 37
Views: 6,229
|
Forum: RIBs & ribbing
04 April 2006, 12:56
|
Replies: 13
Views: 2,080
|
Forum: RIBs & ribbing
24 January 2006, 12:36
|
Replies: 13
Views: 2,778
|
Forum: RIBs & ribbing
24 January 2006, 12:13
|
Replies: 17
Views: 3,701
|
Forum: Inflatable boats - SIBs and folding RIBs
20 July 2005, 13:34
|
Replies: 23
Views: 5,484
Getting Ashore
I HAVE BEEN USING A RING FOR MANY YEARS AND PADDLING IT WITH A FRISBEE :D IT STORES EASLY AND GIVES EVERY ONE A LAUGH. DON,T PADDLE IN STRONG CURRENTS OR WIND OR YOU COULD END UP ANYWARE :glug:
|
Forum: RIBs & ribbing
21 February 2005, 06:36
|
Replies: 13
Views: 3,267
|
Forum: RIBs & ribbing
20 February 2005, 16:29
|
Replies: 13
Views: 3,267
Re moorimg in I.O.W
Hi Roy
I have a house at Island Harbour half way up the Madina river from Cows. I might be able to help you with your mooring.
send me an email to jdarlingto@aol.com. :thumbs:
|
Forum: Bits and pieces
16 January 2005, 08:30
|
Replies: 0
Views: 1,469
Honda Welder/Generator
I have a 11hp Honda welder generator. 180amp ark + 5kv at 240V / 110 and is mounted on a wheeled frame.
This set has had very little use and start well £1100 new i would like £450
If you need any...
|
Forum: RIBs & ribbing
27 December 2004, 19:06
|
Replies: 41
Views: 9,281
|
Forum: RIBs & ribbing
24 November 2004, 18:39
|
Replies: 4
Views: 1,524
anodes
Does anybody know where to get the zinc rod that goes into a Yanmar engine anode???
Buying a set of these for £80 and replacing the ones on the leg as well gets expensive.
Has anyone else found...
|
Forum: Engines & props
12 November 2004, 06:47
|
Replies: 2
Views: 1,900
The Pacific 22 uses a drive shaft with the gear...
The Pacific 22 uses a drive shaft with the gear box bolted to the engine and a direct drive out drive.
the prop in the middle is similar to a small lorry drive shaft and would be no problem getting...
|
Forum: Engines & props
08 November 2004, 22:22
|
Replies: 34
Views: 5,480
|
Forum: RIBs & ribbing
07 November 2004, 22:42
|
Replies: 16
Views: 4,188
|
Forum: Inflatable boats - SIBs and folding RIBs
03 November 2004, 06:41
|
Replies: 6
Views: 4,135
|
Forum: RIBs & ribbing
09 September 2004, 18:37
|
Replies: 13
Views: 2,859
|
Forum: RIBs & ribbing
06 September 2004, 18:15
|
Replies: 13
Views: 2,859
|
Forum: Engines & props
04 September 2004, 07:26
|
Replies: 7
Views: 2,469
|
Forum: Engines & props
21 August 2004, 07:49
|
Replies: 37
Views: 6,731
|
Forum: RIBs & ribbing
31 July 2004, 09:15
|
Replies: 36
Views: 5,862
|
Forum: RIB gallery
30 June 2004, 18:58
|
Replies: 3
Views: 1,715
|
Forum: RIBs & ribbing
18 May 2004, 18:32
|
Replies: 5
Views: 4,781
Thanks Chris for the info, it look about 30-35...
Thanks Chris for the info, it look about 30-35 miles by sea from Bude to Padstow. Is their any major nav hazzards??? and what the chance of just keeping the trailer at Bude as we need the car for the...
|
Forum: RIBs & ribbing
17 May 2004, 18:02
|
Replies: 5
Views: 4,781
Launching at Rock
I am going on holiday at the beginning of July to North Cornwall,
around the Padstow area . I would like to take my 8m Scorpion Rib and launch it at Rock. Has anybody used this slipway. Is there any...
|
Forum: RIBs & ribbing
05 October 2002, 09:36
|
Replies: 6
Views: 6,733
Cobra Ribs
I currently have a Pacific 22 Diesel rib which i have been verv pleased with but i would like more length and a bit more speed.
i am looking at a 8.5m cobra with a 250hp mercruser diesel.
Could...
|