Showing results 1 to 15 of 15
Search took 0.00 seconds.
Search: Posts Made By: playspot1
Forum: RIBs & ribbing 04 June 2003, 17:06
Replies: 4
Views: 2,038
Posted By playspot1
Dive boat RIB size for 90hp Merc???

Hey all,

I have a 2003 90hp 2 Stroke Mercury. (yes 2 stroke, gas is cheap here in Oregon) I purchased this motor for my current RIB with the intention of putting it on a larger boat. Well, the...
Forum: RIBs & ribbing 01 July 2002, 21:08
Replies: 4
Views: 1,936
Posted By playspot1
pinhole leaks & boat update

Hi all,

Ok, with the help of many so far, my RIB is cming along nicely. I've repatched and repaired a previous owners inadequate repair. I've got all the engine, electronics, and steering issues...
Forum: RIBs & ribbing 18 June 2002, 19:01
Replies: 2
Views: 1,299
Posted By playspot1
Brian, Thanks for the info. I have already...

Brian,

Thanks for the info. I have already e-mailed Nick directly, but have not yet heard from him yet, and was hoping somebody else might be able to share their knowledge. From what I gather,...
Forum: RIBs & ribbing 18 June 2002, 18:13
Replies: 2
Views: 1,299
Posted By playspot1
Adhesive/humidity

Hi all,

Does anyone know if humidity will effect Bostic 2402 2-part adhesive? It's currently raining here, and while the boat is under cover, obviously the humidity is close to 100%. I know this...
Forum: RIBs & ribbing 28 May 2002, 20:32
Replies: 6
Views: 2,838
Posted By playspot1
thanks for the replies.... I think you're...

thanks for the replies....

I think you're both right, preparation is most likely the biggest issue. Humidity is what I've now found to really effect the cureing and a good adhesion of the...
Forum: RIBs & ribbing 28 May 2002, 17:56
Replies: 6
Views: 2,838
Posted By playspot1
RIB repair

Hello all!

Need some help on how to repair my rib. Any online info out there that is readily available? The tubes are fine at holding air, no patches needed, but other work needs to be done. ...
Forum: Engines & props 09 April 2002, 03:54
Replies: 19
Views: 4,732
Posted By playspot1
Batfalcon,

Actually I WAS talking about prop drive. I used the example of the jet, but I've done both prop and jet in large engines. Really the whole key is probably the torque of the engine steerer tube. (if...
Forum: RIBs & ribbing 06 April 2002, 19:07
Replies: 5
Views: 2,808
Posted By playspot1
Ok, so the engine is all set now. What great...

Ok, so the engine is all set now. What great help to have experienced people to talk with!! Thanks again!

So the engine will be a new Merc 90hp 2 stroke. The weight of the 75 and the 90 is...
Forum: RIBs & ribbing 06 April 2002, 16:24
Replies: 5
Views: 2,808
Posted By playspot1
5m Dive boat setup

Ok, thanks to everyone, especially to Pete7, I have come to conclusions (pretty much) how I am going to outfit my RIB with motor and steering.

The motor will be a 90hp Merc, (4 stroke or 2 not yet...
Forum: Engines & props 06 April 2002, 16:13
Replies: 19
Views: 4,732
Posted By playspot1
Ok, one last question and I'll be done with this...

Ok, one last question and I'll be done with this thread! I promise!

As I have calculated, fuel is is roughly 1/3 the cost of where most of you are. (more or less) Yes, I feel lucky! To this end,...
Forum: Engines & props 06 April 2002, 01:36
Replies: 19
Views: 4,732
Posted By playspot1
Pete, What will a Merc 90hp 2 stroke burn...

Pete,

What will a Merc 90hp 2 stroke burn per hour? As I said, long runs are not really what will normally be happening with this boat. It's on a trailer, and most dive sites are fairly close to...
Forum: Engines & props 06 April 2002, 00:25
Replies: 19
Views: 4,732
Posted By playspot1
Pete, Thanks for the response!! I have...

Pete,

Thanks for the response!! I have sketched out the arrangements of tanks and gear, and it works great....as long as the divers don't plan on coming along. I know you are right about the...
Forum: Engines & props 05 April 2002, 20:00
Replies: 19
Views: 4,732
Posted By playspot1
I think you are right that a console would...

I think you are right that a console would certainly be a much easier way to go, and most likely I will indeed do so.

With regards to the tiller though, I would have to disagree with you. In...
Forum: Engines & props 05 April 2002, 17:52
Replies: 19
Views: 4,732
Posted By playspot1
Alan, Thanks for the reply. I suppose that...

Alan,

Thanks for the reply. I suppose that we are fairly lucky here that the price of gas is fairly inexpensive. Also, this boat is more intended for short trips, not extended touring, so the...
Forum: Engines & props 05 April 2002, 16:30
Replies: 19
Views: 4,732
Posted By playspot1
Rib Engine sizing help!!

Hello there from Oregon, USA!

RIB use here is very limited, and information is hard to come by, so I would appreciate if some of you could give a piece of advice on adequate engine sizing for a...
Showing results 1 to 15 of 15

 


All times are GMT. The time now is 04:04.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.