Forum: Bits and pieces
26 May 2009, 12:18
|
Replies: 3
Views: 1,133
|
Forum: Bits and pieces
24 May 2009, 16:01
|
Replies: 3
Views: 1,133
|
Forum: Bits and pieces
17 May 2009, 09:41
|
Replies: 5
Views: 3,065
the width of the out board including the tiller...
the width of the out board including the tiller arm is 12.5 inch ive a avon searider 5.4 and when i had it on it i placed the aux to the outside on the outboard bracket so the main engine had full...
|
Forum: Bits and pieces
16 May 2009, 20:21
|
Replies: 5
Views: 3,065
|
Forum: Bits and pieces
16 May 2009, 17:36
|
Replies: 5
Views: 3,065
yamaha 4hp 2 stroke outboard
hi ive a old ish yamaha 4hp outboard standard shaft pull start internal fuel tank plus external conector to go to main tank. starts ok dood condition , prop has a little ding in it but you might be...
|
Forum: RIBs & ribbing
14 October 2008, 16:25
|
Replies: 15
Views: 3,173
|
Forum: RIBs & ribbing
13 October 2008, 16:55
|
Replies: 15
Views: 3,173
just been to a boat jumble and got some glass...
just been to a boat jumble and got some glass matting but the epoxy resin was too expensive for just a small job on my rib, how long would the normal resin last compaired to the exoxy resin. its only...
|
Forum: RIBs & ribbing
04 October 2008, 18:13
|
Replies: 15
Views: 3,173
fiberglassing a anchor box
hi ive a old searider and want to build a anchor box at the front so i can do away with the old barrel, ive pre cut the plywoog sheets to fit and are going to hold in place with pink grip then...
|
Forum: Engines & props
04 September 2008, 17:07
|
Replies: 6
Views: 1,482
ps if anyone has used the whitby slip way into...
ps if anyone has used the whitby slip way into the harbour and used the tap at the top of slip , can you please let me know wot you are using to flush and swill down your craft. as yet im still...
|
Forum: Engines & props
03 September 2008, 16:27
|
Replies: 6
Views: 1,482
|
Forum: Engines & props
02 September 2008, 17:46
|
Replies: 6
Views: 1,482
thanks but ive tyed that and it seems to be a...
thanks but ive tyed that and it seems to be a totaly diffrent size alltogether ive got 1/2 5/8 3/4 1in and still no look in the end we had to hold the connection up to the tap so we could flush our...
|
Forum: Electrics and electronics
01 September 2008, 18:39
|
Replies: 4
Views: 1,642
garmin 160 fishfinder
do fishfinders give a true picture of the fish under the boat or is it just a con. we went out at weekend and moved around and saw loads of fish on the screen so stopped as soon as we did the fish...
|
Forum: Engines & props
31 August 2008, 09:56
|
Replies: 6
Views: 1,482
Hose connector - whitby launch ramp
hi ive just been to whitby this weekend and tryed to couple to the tap but my fittings are either too big or small , i went to the chandlers but he said he only had his own and could not help , where...
|
Forum: Engines & props
30 June 2008, 16:22
|
Replies: 1
Views: 1,317
engine transom clamp
im just about to buy a new mariner 60efi and i am worried that the ptt clamp holes wont match up with the holes already drilled in to hold the engine in place. is every manufacturer plate diffrent,...
|
Forum: Engines & props
22 June 2008, 11:04
|
Replies: 7
Views: 2,220
bill higham / any good
hi ive just been across to bill higham to buy a brand new engine from him, he kept me waiting around for over half a hour, his engines on display wernt that good selection, his second hand engines...
|
Forum: Engines & props
16 June 2008, 14:59
|
Replies: 9
Views: 2,005
i was going to get the tohatsu engine then i...
i was going to get the tohatsu engine then i looked at mariner engines and the 60 bigfoot might be a bit better as its a lot lighter so i might put more money and get that engine, it all depends on...
|
Forum: Engines & props
14 June 2008, 19:30
|
Replies: 9
Views: 2,005
new engine advise please
hello ive got a old avon searider 5.4 and am looking to buy a new engine for it , but im a bit worried about putting a engine thet is too heavy for it ,ive still got the flooding hull so it sits...
|
Forum: RIBs & ribbing
18 February 2008, 17:35
|
Replies: 4
Views: 1,549
|
Forum: RIBs & ribbing
17 February 2008, 15:08
|
Replies: 4
Views: 1,549
cobra ribs whitby ?
hi i was in whitby this saturday and saw 2 nice cobra ribs setting of from harbour one has orange tubes the other blue tubes , was it any one on here they went down to scarborough and when we got...
|
Forum: RIBs & ribbing
22 January 2008, 17:26
|
Replies: 7
Views: 2,841
thanks ashbypower plus every body else by the...
thanks ashbypower plus every body else by the looks of wot youve posted it looks like i was looking at daves launching site pages, which is wot i was wanting ,but my friend as just emailed saying he...
|
Forum: RIBs & ribbing
21 January 2008, 16:18
|
Replies: 7
Views: 2,841
trying to find a web page
hello im trying to find a web site or page i saw last year on the net ,wot it was about as far as i can remember is launching a rib off a break back trailer off a quay side without getting the wheels...
|
Forum: Trailers & towing
14 January 2008, 12:28
|
Replies: 11
Views: 3,528
|
Forum: Trailers & towing
12 January 2008, 13:30
|
Replies: 11
Views: 3,528
|
Forum: Trailers & towing
12 January 2008, 12:27
|
Replies: 11
Views: 3,528
new de graaff trailer
hi am in talks with de graaff but cannot decide which trailer would be best , my rib is a 5.4 avon sea rider , the trailer i want is either the sb1300 2 or the pa 1300 2 the pa has keel rollers but...
|
Forum: Engines & props
27 September 2007, 17:39
|
Replies: 44
Views: 9,658
|