Forum: RIBs & ribbing
21 June 2009, 17:59
|
Replies: 5
Views: 2,141
|
Forum: RIBs & ribbing
19 June 2009, 17:23
|
Replies: 5
Views: 2,141
|
Forum: RIBs & ribbing
16 June 2009, 20:40
|
Replies: 11
Views: 2,449
|
Forum: RIBs & ribbing
16 June 2009, 19:05
|
Replies: 11
Views: 2,449
|
Forum: RIBs & ribbing
16 June 2009, 07:04
|
Replies: 11
Views: 2,449
Luke I may be able to help with a panel if you...
Luke I may be able to help with a panel if you are interested I had a couple made and didn't use the second I'll try and get a picture if it helps it has four switch holes with holes for indicator...
|
Forum: RIBs & ribbing
16 June 2009, 06:59
|
Replies: 11
Views: 2,449
|
Forum: Engines & props
16 June 2009, 06:46
|
Replies: 19
Views: 3,845
Thanks, major effort on your behalf and much...
Thanks, major effort on your behalf and much appreciated. I have tried opening the clock but having undone the nuts on the back and loosened the unit inside the front of the bezel is well and truly...
|
Forum: RIBs & ribbing
13 June 2009, 12:35
|
Replies: 16
Views: 2,847
|
Forum: RIBs & ribbing
13 June 2009, 11:59
|
Replies: 0
Views: 927
Slippery things
I have added some of these:
https://www.screwfix.com/prods/37601/Sealants-Adhesives/Tapes/Anti-Slip-Tapes/Pre-Cut-Anti-Slip-Treads-140-x-140mm-Pack-of-10
to the "unflat" areas inside my RIB. They...
|
Forum: Engines & props
13 June 2009, 11:53
|
Replies: 19
Views: 3,845
|
Forum: RIBs & ribbing
09 June 2009, 17:16
|
Replies: 43
Views: 5,107
|
Forum: RIBs & ribbing
09 June 2009, 17:09
|
Replies: 16
Views: 2,847
|
Forum: RIBs & ribbing
07 June 2009, 07:36
|
Replies: 10
Views: 2,165
It's far more likely that the petrol is "dead"...
It's far more likely that the petrol is "dead" especially if it was in a vented container over the winter. The fuel could be used in a car mixed with lots more or you can add octane booster to...
|
Forum: RIBs & ribbing
06 June 2009, 20:00
|
Replies: 12
Views: 5,851
|
Forum: RIBs & ribbing
06 June 2009, 07:40
|
Replies: 20
Views: 3,430
|
Forum: RIBs & ribbing
05 June 2009, 18:44
|
Replies: 20
Views: 3,430
Stainless steel 304 grade laser cut to size
I'm sure you guys must have your contacts but if you go to Ebay (!) and visit the shop of Profileman you will see he cuts things from stainless marine grade and alluminium. I ordered a couple of...
|
Forum: Engines & props
05 June 2009, 18:38
|
Replies: 19
Views: 3,845
Thanks 9D280, strange name? but this it would...
Thanks 9D280, strange name? but this it would seem may be the solution! The rev counter sits at about 1300 rpm at tickover, a tad too high listening to the engine which is probably at a guess a...
|
Forum: RIBs & ribbing
03 June 2009, 07:40
|
Replies: 3
Views: 1,123
|
Forum: Engines & props
03 June 2009, 07:33
|
Replies: 19
Views: 3,845
The pitch shown on the prop is 286x330 picture...
The pitch shown on the prop is 286x330 picture enclosed of the prop and the gauge. I'll run the engine up in a minute and warm it to see what the gauge says at tickover. I put another Honda on...
|
Forum: RIBs & ribbing
02 June 2009, 21:28
|
Replies: 2
Views: 4,118
Trevor I can't help with the holes location but...
Trevor I can't help with the holes location but can you not clamp the outboard on? If not ALWAYS use a good quality silcone sealant everywhere including in around and on and under the bolts to seal...
|
Forum: Engines & props
02 June 2009, 21:17
|
Replies: 19
Views: 3,845
Ooops
Looks like this might be difficult I do not know any speeds as we don't have anything fitted yet that will gauge speed. I also haven't got a clue about prop pitch I'll take some pictures and see what...
|
Forum: Engines & props
02 June 2009, 09:13
|
Replies: 19
Views: 3,845
My new outboard
Hi eveyone, at long last I managed to get out on the water. Spent a couple of hours out on the Solent yesterday brilliant weather and a fantastic feeling after not Ribbing for so long. It was the...
|
Forum: RIBs & ribbing
14 May 2009, 21:37
|
Replies: 3
Views: 1,030
Thanks JKY sadly you seem to be the only one!!...
Thanks JKY sadly you seem to be the only one!! Makes me feel a bit lonely as I was hoping for some help as well as a greeting! but you are very kind and the Good Lord permitting I may be around to...
|
Forum: RIBs & ribbing
13 May 2009, 08:36
|
Replies: 3
Views: 1,030
Hoping to be back....
Hello All!
I have not been to RIBnet for some time, a combination of house rebuilding (its a bit like the RIB; never quite finished) and not being too well. I have actually not put my Avon Searider...
|
Forum: RIBs & ribbing
04 June 2007, 09:07
|
Replies: 10
Views: 2,252
|