Forum: Engines & props
31 May 2019, 20:23
|
Replies: 169
Views: 64,182
Hi Jeff thanks for that. I found google to be...
Hi Jeff thanks for that. I found google to be deficient in anything for it however I did find better info on page 62 - 64 of the manual. Couldn't see for looking!
Only worry is that the wire...
|
Forum: Engines & props
31 May 2019, 19:23
|
Replies: 169
Views: 64,182
|
Forum: Engines & props
23 May 2019, 19:40
|
Replies: 169
Views: 64,182
|
Forum: Engines & props
23 May 2019, 12:55
|
Replies: 169
Views: 64,182
|
Forum: Engines & props
14 June 2016, 21:27
|
Replies: 117
Views: 27,396
|
Forum: Engines & props
05 June 2016, 19:10
|
Replies: 117
Views: 27,396
|
Forum: Engines & props
05 June 2016, 19:10
|
Replies: 117
Views: 27,396
|
Forum: Engines & props
04 June 2016, 19:15
|
Replies: 117
Views: 27,396
|
Forum: Engines & props
04 June 2016, 16:16
|
Replies: 117
Views: 27,396
Getting back on topic...
It’s...
Getting back on topic...
It’s taken a while but I finally have some useful info to post about the servicing and the prop selection which started this whole thread off. I apologise up...
|
Forum: Electrics and electronics
19 May 2016, 21:56
|
Replies: 57
Views: 12,249
|
Forum: Engines & props
14 May 2016, 18:39
|
Replies: 117
Views: 27,396
Agreed, special tools don't count. They always...
Agreed, special tools don't count. They always pay for themselves if you keep things long enough - as I clearly do!
When t was 10 months old my Sierra went into an RS Ford dealer for a steering...
|
Forum: Engines & props
13 May 2016, 21:52
|
Replies: 117
Views: 27,396
"Serviced in accordance with the service...
"Serviced in accordance with the service schedule"
Yes well there seems to be a fair few versions of that, so which did they use for you?
I'd pay £125 a year to keep the warranty valid so long...
|
Forum: Engines & props
13 May 2016, 16:55
|
Replies: 117
Views: 27,396
Yes they're doing a combined one. My engine was...
Yes they're doing a combined one. My engine was over a month old before it went in the water so to do a service at 1 month is just nuts in my view. The dealer in Plymouth agreed that this is often...
|
Forum: Engines & props
13 May 2016, 12:23
|
Replies: 117
Views: 27,396
|
Forum: Engines & props
12 May 2016, 13:59
|
Replies: 117
Views: 27,396
|
Forum: Engines & props
12 May 2016, 13:35
|
Replies: 117
Views: 27,396
|
Forum: Engines & props
12 May 2016, 11:59
|
Replies: 117
Views: 27,396
So after asking my supplying dealer for a...
So after asking my supplying dealer for a breakdown of the service cost into parts and labour and asking why he was doing things from the 2nd and third year service in the first year he stopped...
|
Forum: Electrics and electronics
10 May 2016, 13:15
|
Replies: 57
Views: 12,249
|
Forum: Electrics and electronics
10 May 2016, 12:44
|
Replies: 57
Views: 12,249
|
Forum: Electrics and electronics
10 May 2016, 12:43
|
Replies: 57
Views: 12,249
|
Forum: Electrics and electronics
10 May 2016, 12:38
|
Replies: 57
Views: 12,249
|
Forum: Electrics and electronics
10 May 2016, 12:05
|
Replies: 57
Views: 12,249
There's gonna be an awful lot of disturbance...
There's gonna be an awful lot of disturbance close to the motor as the leg ploughs through the water and if I read your post correctly, your transducer is between the tab and the leg. Not a good...
|
Forum: Electrics and electronics
10 May 2016, 08:34
|
Replies: 57
Views: 12,249
I've attached a photo of my transducer mount on...
I've attached a photo of my transducer mount on the ribeye. Due to the Ally Hull construction there is a lip protruding aft of the transom and it was too big to allow direct mounting so I cut a piece...
|
Forum: Engines & props
09 May 2016, 08:54
|
Replies: 117
Views: 27,396
I'm with Fenlander on the pitch selection. You...
I'm with Fenlander on the pitch selection. You can divide rpm by the gearbox reduction, multiply that by pitch inches and divide that into a mile of inches but it won't really tell you anything. Each...
|
Forum: Engines & props
06 May 2016, 20:41
|
Replies: 117
Views: 27,396
No Problem. What would be good would be for a...
No Problem. What would be good would be for a bunch of us owners to club together to buy a few of the special tools such a flywheel puller for the timing belt change though that may be "fabricatable"...
|