Forum: Engines & props
26 September 2001, 00:08
|
Replies: 4
Views: 2,283
|
Forum: Engines & props
21 September 2001, 15:00
|
Replies: 4
Views: 2,283
|
Forum: RIBs & ribbing
21 September 2001, 05:13
|
Replies: 5
Views: 2,010
|
Forum: RIBs & ribbing
13 September 2001, 03:57
|
Replies: 0
Views: 1,628
|
Forum: RIBs & ribbing
13 September 2001, 03:55
|
Replies: 3
Views: 2,000
Yes I did check out the Polaris, at their...
Yes I did check out the Polaris, at their factory, not with sea trials. They make two boats in the 4.5 neighborhood, both fairly deep vee, 22 degree deadrise, actually same hull. The boats are, by...
|
Forum: RIBs & ribbing
12 September 2001, 00:40
|
Replies: 4
Views: 2,053
|
Forum: RIBs & ribbing
09 September 2001, 16:16
|
Replies: 3
Views: 2,000
Good sea boats around 4.5M ?
I still trying to figure out what boat to buy and I don't have the huge and vigorous UK market to shop in: yes, I'm jealous! I'm in Washington State in a little backwater town on the outskirts of...
|
Forum: RIBs & ribbing
09 September 2001, 16:08
|
Replies: 16
Views: 5,681
|
Forum: Electrics and electronics
07 September 2001, 05:03
|
Replies: 25
Views: 6,146
|
Forum: RIBs & ribbing
07 September 2001, 04:57
|
Replies: 2
Views: 2,500
|
Forum: RIBs & ribbing
06 September 2001, 16:32
|
Replies: 6
Views: 4,142
towing a rib
I agree completely about the potential risks of towing in very rough (especially following seas) conditions. I almost lost my Zodiac MK II years ago while sailing down the Pacific coast. It, too...
|
Forum: RIBs & ribbing
06 September 2001, 16:27
|
Replies: 2
Views: 2,500
Polaris Seamaster Rib 4.4 (canada)
Does anyone know anything about the reputation of this company or their boats. They apparently compete with Zodiac Hurricane on government contracts.
Nick
|
Forum: RIBs & ribbing
05 September 2001, 17:04
|
Replies: 6
Views: 4,142
ribcraft 4.8 and 4.2
I'm looking for a RIB that doesn't seem to exist in the US market place and the boat I have in mind in the British market is the ribcraft 4.8: rugged, good chop handling hull form, jockey seat set...
|
Forum: Engines & props
05 September 2001, 16:14
|
Replies: 6
Views: 6,136
|
Forum: Engines & props
03 September 2001, 21:33
|
Replies: 6
Views: 6,136
Tohatsu 50 TLDI
A Seattle dealer told me about the Tothatsu 50 with digitally controlled low pressure injection, and I have been reading about it on various internet sources. The injection system was developed by...
|
Forum: Engines & props
03 September 2001, 21:27
|
Replies: 3
Views: 2,512
caribe delux 13
The delux 13 is apparently a different model than previous 13's and isn't listed yet in the caribe spec sheet. A couple of dealers have told me that it is the first of a new series of hull design...
|
Forum: Engines & props
03 September 2001, 01:01
|
Replies: 3
Views: 2,512
Honda or Yamaha 50???
Greetings to everyone from a first time poster and a new member. I am in the fairly rib-less USA and am just about to buy my third small rib. The last was an AB AL3.50 and Now I'm looking seriously...
|