Forum: Engines & props
07 January 2017, 09:58
|
Replies: 3
Views: 990
|
Forum: Engines & props
06 January 2017, 17:06
|
Replies: 3
Views: 990
Yamaha 60fet 2 stroke.
Hi I recently acquired a 60fet as spares for my 50 deto but the leg and gearbox look different and the hood is different. Anyone know what this engine shares parts with? Is it the 75 85 90hp or is it...
|
Forum: RIBs & ribbing
05 June 2016, 11:18
|
Replies: 47
Views: 9,019
Flipped the boat over to look at the bottom and...
Flipped the boat over to look at the bottom and found millions of repairs. We're going to take them out and redo them then glass the whole centre up with another two layers of glass before sanding it...
|
Forum: RIBs & ribbing
04 June 2016, 14:01
|
Replies: 47
Views: 9,019
|
Forum: RIBs & ribbing
08 May 2016, 08:37
|
Replies: 47
Views: 9,019
|
Forum: RIBs & ribbing
07 May 2016, 20:28
|
Replies: 47
Views: 9,019
Tonight we got the underside of the deck...
Tonight we got the underside of the deck flowcoated and ready to glass in. We used red flowcoat as we had it lying about and wanted to save the orange for the deck and bits that get seen. We glassed...
|
Forum: RIBs & ribbing
07 May 2016, 20:22
|
Replies: 47
Views: 9,019
|
Forum: RIBs & ribbing
07 May 2016, 10:56
|
Replies: 47
Views: 9,019
No. There is 2 sheets of ply. The plan is 2...
No. There is 2 sheets of ply. The plan is 2 layers of 300 gsm csm behind the first layer of ply then 1 layer of csm between the second layer of ply and then 2 or 3 layers of csm over the top.
|
Forum: RIBs & ribbing
07 May 2016, 10:38
|
Replies: 47
Views: 9,019
After a while We have finally got back on with...
After a while We have finally got back on with the rib. We got all the floor fully cut out. There were a few places where theyre was either damage or we went through with the grinder which we have...
|
Forum: RIBs & ribbing
04 January 2016, 12:45
|
Replies: 47
Views: 9,019
Okay, so to add more buoyancy to the stern I...
Okay, so to add more buoyancy to the stern I didn't want to use expanding foam again so my dad suggested to use polystyrene foam blocks. Still not sure of what thickness ply to use, any idea's? What...
|
Forum: RIBs & ribbing
02 January 2016, 20:01
|
Replies: 47
Views: 9,019
|
Forum: RIBs & ribbing
28 May 2015, 16:24
|
Replies: 47
Views: 9,019
|
Forum: RIBs & ribbing
25 May 2015, 09:20
|
Replies: 47
Views: 9,019
Im not sure what would be best as I want it for...
Im not sure what would be best as I want it for general playing about but my dad and sister do diving so sitting arround waiting would be better with it flooding. We do watersports so blocked would...
|
Forum: RIBs & ribbing
24 May 2015, 17:51
|
Replies: 47
Views: 9,019
|
Forum: RIBs & ribbing
24 May 2015, 09:06
|
Replies: 47
Views: 9,019
Yep its a big strip but it would be a shame to...
Yep its a big strip but it would be a shame to scrap it as there must of been so much effort gone into building it. The keel isnt as bad as I thought except from the thousand holes in the bottom off...
|
Forum: RIBs & ribbing
23 May 2015, 19:52
|
Replies: 47
Views: 9,019
|
Forum: RIBs & ribbing
23 May 2015, 19:50
|
Replies: 47
Views: 9,019
After giving the tubes and inside the deck a...
After giving the tubes and inside the deck a better clean up we flipped it over to take the stainless plate off the bottom. It was held in with hundreds of self tapping screws. Once I got the plate...
|
Forum: RIBs & ribbing
12 May 2015, 20:46
|
Replies: 47
Views: 9,019
|
Forum: RIBs & ribbing
12 May 2015, 20:31
|
Replies: 47
Views: 9,019
Just took the old console out and tryed the new...
Just took the old console out and tryed the new one that Phil M kindly sold to us, one of the best bits about it was the price, beer and I am not old enough to buy it so got out of paying therefore...
|
Forum: RIBs & ribbing
11 May 2015, 07:07
|
Replies: 47
Views: 9,019
|
Forum: RIBs & ribbing
10 May 2015, 19:46
|
Replies: 47
Views: 9,019
|
Forum: RIBs & ribbing
10 May 2015, 16:47
|
Replies: 47
Views: 9,019
|
Forum: RIBs & ribbing
10 May 2015, 15:48
|
Replies: 47
Views: 9,019
|
Forum: RIBs & ribbing
10 May 2015, 13:05
|
Replies: 47
Views: 9,019
|
Forum: RIBs & ribbing
10 May 2015, 13:03
|
Replies: 47
Views: 9,019
First boat sr4 project
Hi people this is my first post I've been watching my dad's account (beamishken) for ages but just got my first boat that my dad's going to help me do up.
It's an sr4 we bought from davie off the...
|