Forum: RIBs & ribbing
17 April 2016, 22:00
|
Replies: 22
Views: 3,903
|
Forum: Electrics and electronics
03 February 2016, 18:14
|
Replies: 16
Views: 2,309
|
Forum: Electrics and electronics
29 July 2015, 21:15
|
Replies: 40
Views: 5,656
I cant see why this setup would not work? the...
I cant see why this setup would not work? the cost of the UK Navioics chart is a fraction of that of a local one on a mem card (I think about £40). Once you sort the waterproof bit out my only...
|
Forum: RIBs & ribbing
04 July 2015, 14:10
|
Replies: 21
Views: 8,089
|
Forum: Electrics and electronics
18 June 2015, 17:50
|
Replies: 14
Views: 5,200
|
Forum: Electrics and electronics
10 May 2015, 22:05
|
Replies: 16
Views: 3,388
I purchased the exact one from that dealer for...
I purchased the exact one from that dealer for £349 last December I cannot fault it, bear in mind you have to pay extra for the charts though. I bought navionics and downloaded some software for my...
|
Forum: RIBs & ribbing
22 March 2015, 15:41
|
Replies: 61
Views: 16,012
Tested this weekend with a new 15" prop, with...
Tested this weekend with a new 15" prop, with three onboard and full tank got to 5100rpm running at 38mph so quite pleased with that! Thanks for your advice Dave, just need some warmer weather now!...
|
Forum: RIBs & ribbing
05 March 2015, 22:11
|
Replies: 19
Views: 5,136
|
Forum: Bits and pieces
03 March 2015, 22:23
|
Replies: 10
Views: 2,648
|
Forum: Electrics and electronics
02 March 2015, 21:54
|
Replies: 2
Views: 928
|
Forum: Electrics and electronics
02 March 2015, 21:53
|
Replies: 2
Views: 928
|
Forum: RIBs & ribbing
04 February 2015, 21:56
|
Replies: 6
Views: 2,228
|
Forum: RIBs & ribbing
30 January 2015, 14:57
|
Replies: 6
Views: 3,953
|
Forum: RIBs & ribbing
19 January 2015, 20:20
|
Replies: 7
Views: 3,019
searider milpro 4.7 console offset
I believe the offset is to counter prop torque but also to make room for a casualty to lie down on the military boats, as for the skiing, with a decent outboard it will tow a skier all day long!
😃😃
|
Forum: RIBs & ribbing
17 January 2015, 09:02
|
Replies: 22
Views: 5,069
|
Forum: RIBs & ribbing
07 January 2015, 18:34
|
Replies: 12
Views: 7,431
|
Forum: RIBs & ribbing
31 December 2014, 13:48
|
Replies: 61
Views: 16,012
Didn't really push the lever that hard, I will...
Didn't really push the lever that hard, I will have a look and also take it on another run next week. I'll test a few things and hopefully get it right by spring. I'll let you know the outcome of my...
|
Forum: RIBs & ribbing
31 December 2014, 09:51
|
Replies: 61
Views: 16,012
|
Forum: RIBs & ribbing
30 December 2014, 22:38
|
Replies: 61
Views: 16,012
Cheers Dave ill get that sorted for tomorrow I...
Cheers Dave ill get that sorted for tomorrow I dont think it was serviced because the chap I had if off bought it Dec 2008 and it was due first service Dec 11 but so very little use. It was showing...
|
Forum: RIBs & ribbing
30 December 2014, 22:15
|
Replies: 61
Views: 16,012
|
Forum: RIBs & ribbing
30 December 2014, 21:16
|
Replies: 61
Views: 16,012
Yes i did think that as the spec says 5000-5500...
Yes i did think that as the spec says 5000-5500 for this motor, I did have 3 adults onboard and 70l fuel but I will try and drop to a 15, I was just not sure to buy one or try and lend one. I plan on...
|
Forum: RIBs & ribbing
29 December 2014, 20:33
|
Replies: 61
Views: 16,012
I would give it a go, I think the shape of the...
I would give it a go, I think the shape of the hull also plays a part, with a deep V the cav plate can be higher than the bottom of the hull.
Mine is about 1 1/2 inches above but cannot go any lower...
|