Forum: Inflatable boats - SIBs and folding RIBs
12 June 2016, 14:36
|
Replies: 1
Views: 903
|
Forum: Inflatable boats - SIBs and folding RIBs
06 June 2016, 15:54
|
Replies: 1
Views: 903
Replacing F470 Overpressure Valve
I noticed yesterday that I was starting to lose air in the rear segment, some quick investigating with a spray bottle and soap solution confirms that I've got a leak at the rubber gasket underneath...
|
Forum: Inflatable boats - SIBs and folding RIBs
23 September 2015, 18:57
|
Replies: 60
Views: 30,062
|
Forum: Inflatable boats - SIBs and folding RIBs
10 September 2015, 21:26
|
Replies: 60
Views: 30,062
|
Forum: Inflatable boats - SIBs and folding RIBs
29 June 2015, 05:40
|
Replies: 60
Views: 30,062
|
Forum: Inflatable boats - SIBs and folding RIBs
29 May 2015, 03:11
|
Replies: 60
Views: 30,062
|
Forum: Inflatable boats - SIBs and folding RIBs
28 May 2015, 22:05
|
Replies: 60
Views: 30,062
|
Forum: Inflatable boats - SIBs and folding RIBs
28 May 2015, 20:51
|
Replies: 60
Views: 30,062
|
Forum: Inflatable boats - SIBs and folding RIBs
28 May 2015, 20:50
|
Replies: 60
Views: 30,062
|
Forum: Inflatable boats - SIBs and folding RIBs
28 May 2015, 18:11
|
Replies: 60
Views: 30,062
We went up the Nestucca river out to the mouth...
We went up the Nestucca river out to the mouth around Pacific City. Haven't tried a direct surf launch yet... I'd need a bigger towing vehicle than my Subaru to make sure I didn't get stuck on the...
|
Forum: Inflatable boats - SIBs and folding RIBs
28 May 2015, 18:00
|
Replies: 60
Views: 30,062
|
Forum: Inflatable boats - SIBs and folding RIBs
29 August 2014, 16:13
|
Replies: 60
Views: 30,062
Nice, thanks for the info!
Yes, I did...
Nice, thanks for the info!
Yes, I did notice that you can let air out quickly just by pulling the valve body against the spring. I think I did about the same with the retaining nuts on my valves,...
|
Forum: Inflatable boats - SIBs and folding RIBs
18 August 2014, 20:58
|
Replies: 60
Views: 30,062
|
Forum: Inflatable boats - SIBs and folding RIBs
18 August 2014, 05:13
|
Replies: 60
Views: 30,062
|
Forum: Inflatable boats - SIBs and folding RIBs
07 July 2014, 23:18
|
Replies: 60
Views: 30,062
So I discovered what can happen when you pound...
So I discovered what can happen when you pound the crap out of the boat on choppy water.... the rubber tube connecting the main tube to the speed tube can work its way off the fitting and instantly...
|
Forum: RIBnet North America
24 December 2013, 16:04
|
Replies: 47
Views: 10,226
They aren't really "stand up" although you can...
They aren't really "stand up" although you can fill them that way. I just use it laying flat in the bottom of my boat, don't really attach it to anything. It does have several D-rings on the bottom...
|
Forum: RIBnet North America
24 December 2013, 15:42
|
Replies: 47
Views: 10,226
|
Forum: RIBnet North America
24 December 2013, 15:34
|
Replies: 47
Views: 10,226
|
Forum: Inflatable boats - SIBs and folding RIBs
26 November 2013, 14:08
|
Replies: 60
Views: 30,062
On the seized valve, I'd bet that it's the...
On the seized valve, I'd bet that it's the cap/handle that's bent and not the actual brass cone since that part is quite heavy duty. Have you tried using a couple large flat bladed screwdrivers to...
|
Forum: Inflatable boats - SIBs and folding RIBs
02 November 2013, 17:32
|
Replies: 60
Views: 30,062
|
Forum: RIBnet North America
29 October 2013, 18:32
|
Replies: 47
Views: 10,226
|
Forum: RIBnet North America
29 October 2013, 18:29
|
Replies: 47
Views: 10,226
|
Forum: RIBnet North America
28 October 2013, 21:22
|
Replies: 47
Views: 10,226
I use a conventional T-handle hand pump.
...
I use a conventional T-handle hand pump.
The intercommunication valve settings are actually just dependent on the orientation of the brass valve cone to the molded handle on the outside. So if...
|
Forum: Inflatable boats - SIBs and folding RIBs
28 October 2013, 21:04
|
Replies: 60
Views: 30,062
|
Forum: RIBnet North America
28 October 2013, 21:00
|
Replies: 47
Views: 10,226
|