Atlantic 21 Project

[nugent]

seams like an age getting no where fast now,
way to busy at work, managed to put 5 hrs into it today sad times, thought i would have her done by now

rails drilled ready to go 350 bloody holes

made some fibre glass type thinger me jig

fitted said thingy to console

[nugent]

console pretty much fitted out now

stainless back rests

seats are being picked up wednesday

these totems are a pain in my back side this is why iv have had to slow the build down

[Dhf]

Fantastic job your doing there fella, She looks great, I've been following your thread with much interest and look forward to seeing completion, Have you decided where to launch yet, If its anywhere round my way, get in touch and i'll get out for a blast with you.
Regards
Paul.

[nugent]

Originally Posted by Dragonhawk ficht

Fantastic job your doing there fella, She looks great, I've been following your thread with much interest and look forward to seeing completion, Have you decided where to launch yet, If its anywhere round my way, get in touch and i'll get out for a blast with you.
Regards
Paul.

All going well north Wales DM is assisting in her first outing. Not quite sure where or what slip he uses
Really need to get it done,
I shall have the powerhead rebuilt and all rigging complete next 2 weeks,

It's fitting the tubes that are going to cause me issues, I can not do it at home as it will not fit on drive and I need the fork lift to make it easy to do so.
I can. Not get it in at work as we are chock a block with Olympic signage, It will all be gone by end June,, bloody kill me waiting that long I did most of the Graft in 5 days now it's all waiting time

Fingers crossed June bank holiday in the Water',,,,burn some Fuel. Lots of it

Sent from my iPad using Rib.net

[Jizm]

Originally Posted by nugent

err it came from Ozz

http://www.ebay.co.uk/itm/2708965107...84.m1439.l2649

i just liked it i saw it on my freinds boat when i was over there for a month looked impressive,

Is it the same as this one?

http://item.mobileweb.ebay.co.uk/vie...w=220977109468

[nugent]

Originally Posted by Jizm

Is it the same as this one?

http://item.mobileweb.ebay.co.uk/vie...w=220977109468

looks the same to me Sir, defo cheaper than p+p from ozz

good find

[nugent]

finaly back at her

time to get this craft finished,
really does seam a bloody age since i done anything to it,

finished fitting up console

flo coated to orange around seats and console

flo coated in side pods and console

run a ton of wiring and saddle clamps to keep it all tidy

fitted auto bilge pump

run fuel lines

pondering where to fit remote oil tank ( thinking one of back seat pods)

purchased battery's cheap not told wife they was a nifty lol

finally worked out a jig to roll extrusion for tube rails

[nugent]

going to mask and recoat anti slip coat in an hr or so once my flo coat has gone off, give the wife sumat to moan about

A-frame off in the morning also the engine need to re jig some bits on the back end plus sort out fixings through hull for same

colour match transom to hull

run bilge pipe

considering changing the engine now,
shall see what happens monday as i am awaiting to here from the states i had the block machined for a new liner only to find out they sent me the incorrect one defo not kin happy

all going well, now that i have sussed out shaping the tube rails i shall fit them to hull

[nugent]

all seats are now upholsterd

got to change locker door on console to a black one

sortr out fuel fillers and tank gauges

fit tubes

and its there,, just a big engine decision to make

[DM]

Originally Posted by nugent

Not quite sure where or what slip he uses

Port Dinorwic.

ps. pull yer finger out.

[nugent]

Originally Posted by DM

Port Dinorwic.

ps. pull yer finger out.

not me its the poxy Olympics interfering,,,
dont panic you are my test pilot on this one

[falcon0310]

what did you use afer the flow coat as anti slip ? as i have tonardo atm, and flow coat needs sanding, as never been cleaned in its life ex dive rib tried to cut the consol back in and you can black stains in the gel, not even acid touched it adrian

[nugent]

Originally Posted by falcon0310

what did you use afer the flow coat as anti slip ? as i have tonardo atm, and flow coat needs sanding, as never been cleaned in its life ex dive rib tried to cut the consol back in and you can black stains in the gel, not even acid touched it adrian

I purchased non slip flo coat from east coast supplies

http://www.ecfibreglasssupplies.co.u...attopcoat.aspx

Sent from my iPad using Rib.net

[nugent]

been one of them days again lots done but its all out of site.

floor looks 100% better now though

[nugent]

pretty much there now

tube rails are killing me... need to make a decision on how or what to be doing here

[Nick Hearne]

Originally Posted by nugent

pretty much there now

tube rails are killing me... need to make a decision on how or what to be doing here

Don't wish to alarm you but I think something is missing from your engine!


Looking very good indeed you should be very pleased with your self

[nugent]

Originally Posted by Nick Hearne

Don't wish to alarm you but I think something is missing from your engine!


Looking very good indeed you should be very pleased with your self

Lol
It's worse than the visual missing item, the power heads sitting on my work bench at home

Sent from my iPad using Rib.net

[nugent]

not wanting to bore people but chuff me 3.30am start today,,

interesting bits to follow end of play today,, its there i can see light at the end of 'D; tunnel

[nugent]

nice looking engine

[nugent]

Righto then the end is here

After many months of being messed about, struggling for the correct engine internal Gubbins, and some untoward machining and the time consumed doing so

Purchased this steed---

The things you do to get your hands on a decent lump, 2002 200hp merc one owner from new, he purchased the package 2002 and has religiously maintained it there after, I have all original purchase receipt’s, also service invoice’s, for every season on his engine servicing, also he has given me a folder with launch passes, Err 10 to 16 times every year little hrs. Run time on this for sure looks brand fire new,
(oh its used in a river for ski-ing no salt been on here)

Bless him he even had it serviced on 30th may this year just for me,
I think he was a little miffed when I told him within a hr. of getting it home the engine will be removed and it will be straight on flee-bay, for sale that very day.

LOL, any one want a real nice very bloody tidy speed boat, the tower must be £1500 quid’s worth alone;