A confession and some advice please

keg · 22 September 2014, 10:54

Had a great afternoon on Windermere, perfect weather etc. The lake is low at the moment so getting the SR back on the trailer was fun.

It wasn't quite central so me and my bro adjusted it manually...

Asked wife to pull forward gently and as i had not attached the strop to the front, it slid gently off the back.

Winched it back on again, all fine, will always double check that in future. Also forgot to tilt the outboard back up again as we pulled it out of the boat space..

When putting the cover back on, i noticed the attached on one of the chines, it looks like some filler has come out.

Advice please on how best to repair

Phil M · 22 September 2014, 11:36

That looks like an old repair that has come out. I had similar on mine (which has also taken an unintended trip down a slip), which i cleaned out to give a good surface to add gelcoat filler (made by plastic padding I think). I built up the layers and sanded flush, then went over with a few coats of flow coat, then sanded back again and polished. Might not be the best method but it is solid and watertight.

Phil M

C-NUMB · 22 September 2014, 15:28

Might be wrong but it looks like something more than just a gelcoat filler job in my eyes?

macattack101 · 22 September 2014, 15:33

Quote:

Originally Posted by C-NUMB

Might be wrong but it looks like something more than just a gelcoat filler job in my eyes?

Defo on that
Gel goat is for surface scratches which yours isn't. Needs resin and weave. Not that expensive but worth getting a professional in for it.

keg · 22 September 2014, 16:00

Thanks for the replies chaps, i can see a small hole on the left of the filler so assume it goes through. It's a flooding hull.

Any idea of cost please. I can't see a way of getting to the inside of the outer hull.

Luckily it only slid off the trailer and stopped on the beach....

Chris Caton · 22 September 2014, 16:09

if I were you I'd be asking Edd, Nugent on RIBnet, or Mime Whitham of Whitham Glassfibre to be av'ing a look at it for you, that needs a good sorting before it gets any worse

keg · 22 September 2014, 16:17

Thanks Chris, are any of them near Leeds and any rough estimate of cost? ME thinks either i did not notice it when i looked round the boat which is likely as it is on the chine that rests on a bunk or it has started to come off once in the water.

Chris Caton · 22 September 2014, 18:16

Mike is near Ormskirk, Lancs, Edd is Wolverhampton way'ish, give or take a county or two, sorry don't know anyone Leeds way, but maybe someone else will, but I do know both Mike's n Edd's work to be top notch, n you get what you pay for

nugent · 22 September 2014, 19:43

Evening

Chris. Will have to,put you on the pay roll ,,

Mike is closer to you for sure,,, nominee can price with out viewing. ,, main thing is getting it all dried out thoroughly before any repairs can take place

Looks like a previous un skilled repair has let loose

nugent · 22 September 2014, 19:44

M5 junc 4 for the record

Funny heard a rumour I was being called the biffer of West Midlands ,, if only I had half his knowledge and skill level

Chris Caton · 22 September 2014, 20:17

always happy to reccomend good workmanship Edd

keg · 23 September 2014, 07:58

Thanks everyone, you have been stars! Ormskirk is not too far, just about an hour. Are we talking £100s or £1000s do you think?

It's a really tidy boat, perfect for me and didn't cost a lot.

Will ring Mike this morning.

Thanks again everyone.

nugent · 23 September 2014, 09:07

Quote:

Originally Posted by keg

Thanks everyone, you have been stars! Ormskirk is not too far, just about an hour. Are we talking £100s or £1000s do you think? It's a really tidy boat, perfect for me and didn't cost a lot. Will ring Mike this morning. Thanks again everyone.

Low hundreds

keg · 23 September 2014, 10:31

Thanks for that, was worried it was going to be a biggie.

Spoke to Mike at Whitham, what a top chap! and have sent him some pics as well. Will let you know how i get on.

nugent · 23 September 2014, 14:25

Quote:

Originally Posted by keg

Thanks for that, was worried it was going to be a biggie. Spoke to Mike at Whitham, what a top chap! and have sent him some pics as well. Will let you know how i get on.

Mike will look after you and do a top job trust me,,

Pretty much the only other person that has ever worked on my own craft to date

Chris Caton · 23 September 2014, 16:15

Quote:

Originally Posted by keg

Thanks for that, was worried it was going to be a biggie.

Spoke to Mike at Whitham, what a top chap! and have sent him some pics as well. Will let you know how i get on.

I'm sure Mike will sort you out, he's a gud'un