Reply
 
Thread Tools Search this Thread
 
Old 01 June 2011, 05:58   #1
Member
 
Country: New Zealand
Town: Tauranga
Boat name: Extra Pleasure
Make: Atomix
Length: 5m +
Engine: Outboard 60HP 2Strke
Join Date: Aug 2009
Posts: 182
Rusty Leaf Springs

Hey,

I've noticed the leaf springs on my trailer are really quite rusty.

Now I guess this is to be totally expected, and unavoidable since it's going in salt water pretty regularly (even taking a good fresh water wash after).

My question is... do I need to worry about it, and worry that one day they'll snap right through? Will a simple knock with a hammer and see if they start crumbling confirm if they are ok or not?!!

Cheers
__________________
rjbathgate is offline   Reply With Quote
Old 01 June 2011, 09:30   #2
Member
 
Country: UK - Scotland
Make: HumberOceanOffshore
Length: 8m +
Engine: Volvo KAD300/DPX
Join Date: Oct 2002
Posts: 5,596
Chap them to remove the rust, if they're ok grease them up with water resistant grease. In the old days of leaf springs it was common practise to grease them and bind them with cloth or Denso tape.
__________________
JW.
jwalker is offline   Reply With Quote
Old 01 June 2011, 19:55   #3
Member
 
Country: New Zealand
Town: Tauranga
Boat name: Extra Pleasure
Make: Atomix
Length: 5m +
Engine: Outboard 60HP 2Strke
Join Date: Aug 2009
Posts: 182
Quote:
Originally Posted by jwalker View Post
Chap them
?
__________________
rjbathgate is offline   Reply With Quote
Old 02 June 2011, 11:02   #4
Member
 
Country: UK - Scotland
Make: HumberOceanOffshore
Length: 8m +
Engine: Volvo KAD300/DPX
Join Date: Oct 2002
Posts: 5,596
Sorry, Scottish for tapping (as in with a hammer).
__________________
JW.
jwalker is offline   Reply With Quote
Old 02 June 2011, 17:00   #5
Member
 
Country: USA
Town: Oakland CA
Length: 3m +
Join Date: Feb 2005
Posts: 6,653
Mine got rusty within a month of owning trailer. Liberal amounts of lubricant on the mounts kept squeaks to a minimum, but the springs themselves looked like crap. Didn't worry about it too much until a friend snapped a spring on the drive down. Immediately made plans to replace mine. New ones rusted up again pretty quick, but at least I know they're in a good condition under the rust.

Cheap enough to do - As I recall, 3200# springs were less than $50 US each. I just figure they're on a 3 or 4 year replacement cycle.

I have heard of people pre-treating them prior to installation by immersing them in a vat of heated grease; I don't have the facility or tolerance for mess that that involves.

One of these days, when I get some disposable income (quite a bit, actually), I'm going to convert the trailer to torsion axles and disk brakes. Lose the leaf springs and drum brakes forever.

Luck;

jky
__________________
jyasaki is offline   Reply With Quote
Old 18 June 2011, 14:49   #6
Member
 
Pikey Dave's Avatar
 
Country: UK - England
Town: South Yorks
Boat name: Black Pig
Make: Ribcraft
Length: 5m +
Engine: DF140a
MMSI: 235111389
Join Date: Feb 2008
Posts: 11,865
RIBase
Can't beat a spray down with 50/50 waxoil & diesel
__________________
Rule#2: Never argue with an idiot. He'll drag you down to his level & then beat you with experience.
Rule#3: Tha' can't educate pork.
Rule#4:Don't feed the troll
Pikey Dave is offline   Reply With Quote
Old 18 June 2011, 18:09   #7
Member
 
Country: UK - Scotland
Boat name: No name yet
Make: Avon
Length: 4m +
Engine: Honda BF30
Join Date: Jun 2010
Posts: 153
Surface rust on a spring should never be a problem unless two leafs bind together, spring action requires each leaf to slide over the others. Grease, waxoyl, gear oil etc all work, you used to be able to buy teflon/plastic liners which went between the leafs to stop bind and increase ride quality.

free
__________________
free is offline   Reply With Quote
Old 22 June 2011, 16:08   #8
Member
 
Country: USA
Town: Oakland CA
Length: 3m +
Join Date: Feb 2005
Posts: 6,653
Quote:
Originally Posted by free View Post
you used to be able to buy teflon/plastic liners which went between the leafs to stop bind and increase ride quality.
Never seen that. How do you intall the parts? Leaf speings I use are bolted in the center, and have a metal band clip on one side that keeps them from separating.

jky
__________________
jyasaki is offline   Reply With Quote
Old 24 June 2011, 22:07   #9
Member
 
Country: UK - Scotland
Boat name: No name yet
Make: Avon
Length: 4m +
Engine: Honda BF30
Join Date: Jun 2010
Posts: 153
You have to remove the center bolt and split the leafs (not a big job) before fitting the slippers inbetween. The rebound clips don't get in the road as they are not bolted through. I've seen some Asian marque springs with "plastic" buttons towards the end of the leafs to keep them separated as well.

free
__________________
free is offline   Reply With Quote
Old 25 June 2011, 17:07   #10
Member
 
Country: USA
Town: Oakland CA
Length: 3m +
Join Date: Feb 2005
Posts: 6,653
Thanks, Free; will look into those.

jky
__________________
jyasaki is offline   Reply With Quote
Old 25 June 2011, 22:34   #11
Member
 
Country: UK - Scotland
Boat name: No name yet
Make: Avon
Length: 4m +
Engine: Honda BF30
Join Date: Jun 2010
Posts: 153
Spring Liners with Lip - Speedway Motors, America's Oldest Speed Shop

Even on your side of the pond, to be honest, with all the leafs used in the US, it should be easy to get hold of. Teflon or Delrin are the materials to look for.

free
__________________
free is offline   Reply With Quote
Old 26 June 2011, 09:35   #12
Member
 
Country: USA
Town: Oakland CA
Length: 3m +
Join Date: Feb 2005
Posts: 6,653
Thanks again, Free!

jky
__________________
jyasaki is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off




All times are GMT. The time now is 14:39.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.