TROWELING WITH A 90hp FICHT RAM INJECTION

[rors]

I dont suppose any one would know can you trowel with these EVINRUDE
90 HP FICHT RAM INJECTION engines or will they clog up ?

Thanks in advance Rors

[Mollers]

Are you rendering or skimming?

[Pikey Dave]

For tiling, I find notched is best. Steel gets a smooth finish on concrete, if you want a rough non-slip, try a urethane float. Etecs are rubbish, they weigh too much & the gobbo sticks to the cowls, plus at upto 15 grand a throw, a tad extravagant methinks.

[Mollers]

A short shaft Seagull gives a nice texture to Artex and is easier on the arm.

I have a Marshalltown 11" bricky, might try it behind the dinghy.

[rors]

Ok thanks for the piss take i ment to say TROLLING

Regards
Rors

[martini]

In my experience with Ficht motors it doesn't matter if you go fast or slow, the end result is the same.....*bangclatterclatterclatter*

[Mollers]

Originally Posted by rors

Ok thanks for the piss take i ment to say TROLLING

Regards
Rors

Is that something to do with big ugly f'krs who live under bridges?

[willk]

Originally Posted by Mollers

Is that something to do with big ugly f'krs who live under bridges?

You're a big lad, aren't you Mollers? I thought you lived in St. Mawes, ono ?

[Mollers]

Originally Posted by willk

You're a big lad, aren't you Mollers? I thought you lived in St. Mawes, ono ?

A miss is as good as a mile. I live under Penryn bridge, google it, it's another ugly f'ker.

[A1an]

Originally Posted by martini

the end result is the same.....*bangclatterclatterclatter*

Blimey, theone on ebay doesnt look so appealing now

[Mollers]

Originally Posted by A1an

Blimey, theone on ebay doesnt look so appealing now

Ignore him, this guy has stereo 'bangclatterclatterclatter' when they both run.

[Bigmuz7]

Some amusing reposts none the less gentlemen

I'd suggest to the op, it will be fine for a good while,... just give it the guns on the way home to burn off any oiling it will be fine mind you if you got shagged plugs to start with.. life might not be so easy, but you'd know that with dodgy starting etc

[Pikey Dave]

Originally Posted by martini

In my experience with Ficht motors it doesn't matter if you go fast or slow, the end result is the same.....*bangclatterclatterclatter*

I thought that was Optis

I had a 175 FICHT on the previous boat, no problems, use the proper FICHT oil or XD100 though to keep the carbon down.

[martini]

Originally Posted by Pikey Dave

I thought that was Optis

Touché

[9D280]

I don't know much about the FICHTs, but long term low speed is also a good excuse to get the aux out & give it some exersise!

[rors]

Well lads Thanks for all your jokes and help its been fun all the bast lol
Rors

[EnglishLes]

Rors

I've been on here for about 10 months - getting information on here is a bit like gold mining - you have to go thro' tons of rock to get a solitary nugget but its worth it in the end!

[Erin]

Originally Posted by EnglishLes

Rors

I've been on here for about 10 months - getting information on here is a bit like gold mining - you have to go thro' tons of rock to get a solitary nugget but its worth it in the end!

Very good. There's an abundance of Iron Pyrites too, so take care

[Pikey Dave]

Originally Posted by EnglishLes

Rors

I've been on here for about 10 months - getting information on here is a bit like gold mining - you have to go thro' tons of rock to get a solitary nugget but its worth it in the end!

Sometimes you've just got to kiss a few frogs
It could be worse, humor (sic) is strictly frowned upon on the sceptic run Etec forum, god forbid if JimH catches you enjoying yourself. It can be good sport though if a little too easy sometimes

[willk]

Originally Posted by Pikey Dave

humor (sic) is strictly frowned upon on the sceptic run Etec forum

You mean Septic, dontcher? The Etec Sceptics are all on here, s'far as I can tell