Garage clearout- engine & trailer bits

[9D280]

1 set unbraked 750Kg suspension units with hubs & bearings. Bought to replace the gubbed ones, travelled approx 150 miles / 1 launch before I decided the rest of the trailer wasn't worth resucitating. It's a set of these:
http://www.autow.com/trailer-parts/t...n-braked/AE750
£80.


1 Clamp / Swivel assy off a Light grey Yam 75 3- ram power trim. Includes steering toob No bottom section as it was sold with the PT Make me an offer. Beer is valid.

ditto for a Zuz DT25/30 later version. Includes Longshaft leg & lock - down mechanism. Starboard transom clamp cracked. Again, make me an offer.....

[ollyit]

can I have first dibs on the yam bits, my power trim is shot and been removed, Ill happily arrange everything collection wise - pm'in you my offer

[free]

What sort of age is the Suzi? I've got a DT28 with a broken skeg and bent shaft I need to get round to fixing.

free

[9D280]

Ollyit,

You got PM.



Free,

C.1993 It's one of these:
http://store.brownspoint.com/DT30c/308897.asp
Contents of Figs 18, 19 & 20

Note item 1 on Fig 18 has sheared just above the thread for the "thumbscrew" to clamp it to the transom.

Sounds like you may need the gearbox?

I'l ltry & get pics tonight & post

[Bigmuz7]

Will check to see if my trailer will take a mounting plate for those units, take it its just the units you have ?

[free]

Just re-read your original post, aye, it's the bit below Fig 20 that I need. It's also the older one with the split gear casing I need, unless anyone knows better?

free

[9D280]

Bigmuz,

It's almost a plug'n'play set of suspension - just add wheels & trailer! (it's a set of suspension units, hubs (4x4" studs) & bearings, all nicely greased up and with a round trip to Largs & one launch & recovery under their belt. I must afdmit I now can't remember if they are extended axle or not, will check tonight.

Free,

To be honest I've no idea if the older split 'box will fit that leg or not, but if it's the gearbox you need, my bits aren't going to be much use.


Anyone else that might be reading,

Turns out the Yam bits aren't what Ollyit was after, so they are still available. Having now plugged the camera in to recharge, I will try & get the pics up tonight.

[Rogue Wave]

has the yammi clamp got the flip up bits that the motor rests on in transit and are they still rotating. if so I'd like to buy your bits

[Bigmuz7]

Originally Posted by 9D280

Bigmuz,

It's almost a plug'n'play set of suspension - just add wheels & trailer! (it's a set of suspension units, hubs (4x4" studs) & bearings, all nicely greased up and with a round trip to Largs & one launch & recovery under their belt.

Ahh its the single beam axle I have that bolts to the chassis rail with the suspension integrated .. so no go for me mate .. and its only cos I lazy 8 U bolts and I'm done if I can find the right bit and no welding

[9D280]

Rogue,
Yes, and it works See pics below

Pics of the Suz leg, and Yam Clamp / swivel.

For the suspension, it's A pair of these http://www.autow.com/trailer-parts/t...n-braked/TE750
Mated with a pair of these
http://www.autow.com/trailer-parts/t...-spares/HG505S